Hi,
Thanks for the feedback. Ok this makes sense. I will now look further into gem5 
internals then. By the way, right now I am using /utils/tlm/ patch for hooking 
to SystemC world and was hoping that these semantics would have already been 
dealt with in the patch as the fs.py works with external SystemC so I assumed 
it should work with simple.py system if used unmodified but I am unable to get 
that system running due to the mentioned assertion failure.
Regars, uzair

From: [email protected]
To: [email protected]
Date: Wed, 25 Nov 2015 14:51:06 +0000
Subject: Re: [gem5-users] SystemC coupling with gem5






Hi Uzair,



Your memory system needs to implement the same semantics as the gem5 memory 
system (not just read and write). Have a look at SimpleMemory in src/mem for 
what you need to do. Depending on how you bridge to SystemC, you need to also 
translate from TLM to
 gem5 packets, also for these more complex memory commands.



Andreas





From: gem5-users <[email protected]> on behalf of Uzair Sharif 
<[email protected]>

Reply-To: gem5 users mailing list <[email protected]>

Date: Wednesday, 25 November 2015 at 14:47

To: gem5 <[email protected]>

Subject: Re: [gem5-users] SystemC coupling with gem5







Hi,



I forgot to mention that in this simple.py setup even with membus hooked to 
external world (like in util/tlm/tlm.py) I get the same assertion error so this 
issue is atleast not related to directly hooking CPU to SystemC.



Regards, uzair




From: [email protected]

To: [email protected]

Date: Wed, 25 Nov 2015 15:19:42 +0100

Subject: Re: [gem5-users] SystemC coupling with gem5




Hi,



Thanks guys for the feedback. Well sofar I modified 
/configs/learning_gem5/part1/simple.py system to hook up single CPU's cache 
ports (i/d) as well as system_port to 3 ExternalSlave ports with
membus disabled. From the logs I can see that binary for hello_world is loaded 
followed by a block of memory written via
dcache_port. After that the simulation starts running with IFetches and it 
seems to work fine but I end up with an assertion failure: 




0: system.remote_gdb.listener: listening for remote gdb #0 on port 7000



0 s (=) : sc_main Port Found



0 s (=) : /IEEE_Std_1666/deprecated deprecated constructor: sc_time(uint64,bool)



gem5.opt.sc: build/ARM/mem/request.hh:569: uint64_t Request::getExtraData() 
const: Assertion `privateFlags.isSet(VALID_EXTRA_DATA)' 
failed.



Program aborted at tick 80160000



Aborted (core dumped)



Can you guys point out why this assertion fails as I am not familiar with gem5 
internals?? Is it related to the use of external memory system?? Have I messed 
up somewhere??






Regarding the use of SystemC memory system, actually I have already developed 
SystemC models and used them in ARMv7 based architectures but now I want to 
integrate them with ARMv8 based mutlicore systems which I think are supported 
well by gem5. I can
 use the system.membus-hook-to-SystemC approach but I need to somehow figure 
out which smp-core actually initiated the memory transaction for my cache-algos 
to work. Is this possible within gem5 that somehow I can know initiator-smp 
core via some sort
 of tlm_extension or something else within the SystemC port/target?? This would 
be quite useful and allow me to just hook the
membus which is already done by Matthias work



Regards, uzair 







From: [email protected]

To: [email protected]

Date: Wed, 25 Nov 2015 13:37:26 +0000

Subject: Re: [gem5-users] SystemC coupling with gem5



Hi Uzair,



I think conceptually you should be find doing what you suggest: Connect each 
CPU core directly to two ExternalSlave ports



As Abdul points out though…this is really jumping in at the deep end. 



Andreas





From: gem5-users <[email protected]> on behalf of Abdul Mutaal 
<[email protected]>

Reply-To: gem5 users mailing list <[email protected]>

Date: Wednesday, 25 November 2015 at 13:34

To: gem5 users mailing list <[email protected]>

Subject: Re: [gem5-users] SystemC coupling with gem5







Hi, 



I believe it would be tough to realize a system in gem5 without system bus. It 
would suggest you to keep the membus and play with its parameters so that it 
doesn't effect your simulation (latency or bandwidth). 



I haven't tried but you can also look to run in SE mode. FS seems to be too 
complex for your architecture. 



Regards, 



Abdul Mutaal



2015-11-25 11:43 GMT+01:00 Uzair Sharif 
<[email protected]>:







Hi,





Is it possible that I can hook CPU model within full system to SystemC?? I have 
gone through util/tlm example but that hooks the mem_bus to SystemC module. 

Can I just simply disable all caches, membus, mem_ctrls and connect CPU's 
icache_port, dcache_port to ExternalSlave (like in the TLM example) and 
implement the entire memory system functionality in SystemC?? What should I be 
careful about in doing this??





Regards,

uzair






_______________________________________________

gem5-users mailing list

[email protected]

http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users









-- 






Regards,
Abdul Mutaal 











IMPORTANT NOTICE: The contents of this email and any attachments are 
confidential and may also be privileged. If you are not the intended recipient, 
please notify the sender immediately and do not disclose the contents to any 
other person, use it for
 any purpose, or store or copy the information in any medium. Thank you. 

_______________________________________________ gem5-users mailing list 
[email protected] 
http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users




_______________________________________________ gem5-users mailing list 
[email protected] 
http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users




IMPORTANT NOTICE: The contents of this email and any attachments are 
confidential and may also be privileged. If you are not the intended recipient, 
please notify the sender immediately and do not disclose the contents to any 
other person, use it for
 any purpose, or store or copy the information in any medium. Thank you.



_______________________________________________
gem5-users mailing list
[email protected]
http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users                            
          
_______________________________________________
gem5-users mailing list
[email protected]
http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users

Reply via email to