Hello,
I started designing my system but since there is only* 'mostly_incl'* and
*'mostly_excl'* for *clusivity*, how can i implement a cache with a
*non-inclusive* policy? And how to implement *strictly
inclusive/exclusive *policy? Are
'*mostly_incl*' and '*mostly_excl*' sufficient for this?

kind regards,
Armel
--
*JEATSA TOULEPI Armel*
Étudiant En Génie Informatique
Tel: +237 650771894 / 655296800


Le mer. 10 juil. 2019 à 18:35, Armel Jeatsa <[email protected]> a
écrit :

> Thank you very much for your replies.
> I will start using classic caches since i do not have to modify coherance
> protocol for my work.
>
> kind regards,
> Armel
> --
> *JEATSA TOULEPI Armel*
> Étudiant En Génie Informatique
> Tel: +237 650771894 / 655296800
>
>
> Le mer. 10 juil. 2019 à 18:11, Jason Lowe-Power <[email protected]> a
> écrit :
>
>> Hello, and welcome to the gem5 mailing list :).
>>
>> I suggest, at least as a first pass, using the classic caches, not Ruby.
>> You can check out the Learning gem5 book (learning.gem5.org) to see
>> examples of how to create different kinds of systems that don't necessarily
>> match what's in se.py. The classic caches have an option to be "mostly
>> inclusive" and "mostly exclusive" which might do what you need.
>>
>> I don't know if anyone has tried to have separate L2 instruction and data
>> caches. However, this might "just work" with the classic caches assuming
>> you have separate instruction and data busses (this should be possible). I
>> suggest drawing the system you want to simulate on paper, then trying to
>> create the configuration in gem5.
>>
>> If you want to investigate modifying the cache coherence protocol, or
>> your investigation depends on high-fidelity modeling of the on chip
>> network, then you should use Ruby. In this case, you'll probably have to
>> write a new coherence protocol. You might be able to use other coherence
>> protocols (e.g., MESI_Two_Level) as a starting point, or you might have to
>> develop a new one from scratch (See Part 3 of Learning gem5 for details).
>>
>> Cheers,
>> Jason
>>
>>
>>
>> On Wed, Jul 10, 2019 at 9:41 AM Armel Jeatsa <[email protected]>
>> wrote:
>>
>>> Hello,
>>> I am relatively new in gem5 simulator, i have to design a multiprocessor
>>> architecture with two levels of caches composed of:
>>>
>>>    - At level 1: the usual L1i and L1d caches
>>>    - At level 2 (shared by all processors): L2i and L2d caches, L2i
>>>    inclusive with L1i, and L2d non-inclusive with L1d.
>>>
>>> What is the best solution? Use *Ruby *and* Slicc*, or just *Python* and
>>> *C++*. How should I proceed in this case?
>>> I ask this question because the *System* object in gem5 seems to only
>>> accept an L2 bus.
>>> Thank you in advance.
>>> --
>>> *JEATSA TOULEPI Armel*
>>> Étudiant En Génie Informatique
>>> Tel: +237 650771894 / 655296800
>>> _______________________________________________
>>> gem5-users mailing list
>>> [email protected]
>>> http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users
>>
>> _______________________________________________
>> gem5-users mailing list
>> [email protected]
>> http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users
>
>
_______________________________________________
gem5-users mailing list
[email protected]
http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users

Reply via email to