sure. say hi to norm !
----------------------------------------------------------------------------- David Lee Lead Engineer MarkLogic Corporation [email protected] Phone: +1 812-482-5224 Cell: +1 812-630-7622 www.marklogic.com<http://www.marklogic.com/> From: [email protected] [mailto:[email protected]] On Behalf Of Geert Josten Sent: Tuesday, February 05, 2013 7:18 AM To: MarkLogic Developer Discussion Subject: Re: [MarkLogic Dev General] Not Able To Open Admin Interface Hi Varun, MarkLogic installs itself as a Windows Service, but doesn't mark it for automatic startup. I'm running it under Windows 7 for development purposes, and the first thing I do after a clean install is open the Services page, open the MarkLogic service properties, and mark it for Delayed automatic startup. It gives your box 5 to 10 minutes to fully startup, before MarkLogic fires up, and start claiming resources. Can't recall what happens when you upgrade, but it won't harm to check the service settings again after each installer run. Kind regards, Geert Van: [email protected]<mailto:[email protected]> [mailto:[email protected]<mailto:[email protected]>] Namens Charles Greer Verzonden: maandag 4 februari 2013 19:41 Aan: [email protected]<mailto:[email protected]> Onderwerp: Re: [MarkLogic Dev General] Not Able To Open Admin Interface When I see that page, it's generally because the server's not running. I'm unfortunately not familiar with MarkLogic on Windows -- but I'd expect there to be a new service to start. That file is all that's needed to begin. Oh, here's the link to this part of docs: http://docs.marklogic.com/guide/admin/startstop#id_95335 Did you choose Start > Programs > MarkLogic Server > Start MarkLogic Server yet? Charles On 02/04/2013 03:23 AM, Varun Varunesh wrote: I have already tried to open it in Firefox and also trying to strat ML sever but still it is not working. I have only installed "MarkLogic-5.0-4.1-i686.msi". Is it required to install any other file or not. On Mon, Feb 4, 2013 at 4:39 PM, Ron Hitchens <[email protected]><mailto:[email protected]> wrote: Try another browser, like Firefox or Chrome. IE likes to display "friendly" messages that often mask what the real problems is. It may simply be that MarkLogic was never started. On Feb 4, 2013, at 11:04 AM, Varun Varunesh <[email protected]><mailto:[email protected]> wrote: Hi, I just downloaded Marklogic 5.0 for windows and after installation when I try to open admin interface (http://127.0.0.1:8001/) it gives me a error that "Internet Explorer cannot display the webpage". I have already gone through the documentation there is nothing mentioned about such error. So, please help me to fix this problem. Thanks and Regards, Varun _______________________________________________ General mailing list [email protected]<mailto:[email protected]> http://developer.marklogic.com/mailman/listinfo/general --- Ron Hitchens {mailto:[email protected]} Ronsoft Technologies +44 7879 358 212 (voice) http://www.ronsoft.com +1 707 924 3878 (fax) Bit Twiddling At Its Finest "No amount of belief establishes any fact." -Unknown _______________________________________________ General mailing list [email protected]<mailto:[email protected]> http://developer.marklogic.com/mailman/listinfo/general _______________________________________________ General mailing list [email protected]<mailto:[email protected]> http://developer.marklogic.com/mailman/listinfo/general -- Charles Greer Senior Engineer MarkLogic Corporation [email protected]<mailto:[email protected]> Phone: +1 707 408 3277 www.marklogic.com<http://www.marklogic.com>
_______________________________________________ General mailing list [email protected] http://developer.marklogic.com/mailman/listinfo/general
