On Tue, 22 Sep 2009 04:54:22 -0500 Karun Sharma <karun.sha...@qlogic.com> wrote:
> Please use "-F" option while running the tests. It will ignore the > "Conflicting CPU frequency" errors. You will still see these messages on your > screen, but with "-F", you will also see the results. Which commands are you referring to with the "-F" option? I just did a pull from git://git.openfabrics.org/~mst/perftest.git and I don't see a -F for the commands there. Have these tools moved? Or are you speaking of other tools? I also run into this problem and I have resorted to turning off cpuspeed. Thanks, Ira > > Regards > Karun > > -----Original Message----- > From: general-boun...@lists.openfabrics.org > [mailto:general-boun...@lists.openfabrics.org] On Behalf Of Sneha Mistry > Sent: Tuesday, September 22, 2009 2:35 PM > To: general@lists.openfabrics.org > Subject: [ofa-general] Problem while running ib tests > > Hi, > > I have two Dual port HCAa card.Which I have installed in > same PC. > > I am using OpenSuse 10.3 and installed OFED 1.4. > > If I try to run any IB bandwidth test or latency test it end us with warning > "Conflicting CPU frequency values detected: 2394.000000 != 1596.000000". > > Is it an OFED related problem or Linux kernel problem. > > HCA are connected back to back and output of ibstat is as given below. > --------------------------------------------------------------------------------------------------------- > CA 'mthca0' > CA type: MT25208 (MT23108 compat mode) > Number of ports: 2 > Firmware version: 4.8.200 > Hardware version: 20 > Node GUID: 0x0002c90200283734 > System image GUID: 0x0002c90200283737 > Port 1: > State: Active > Physical state: LinkUp > Rate: 20 > Base lid: 1 > LMC: 0 > SM lid: 1 > Capability mask: 0x02510a6a > Port GUID: 0x0002c90200283735 > Port 2: > State: Initializing > Physical state: LinkUp > Rate: 20 > Base lid: 0 > LMC: 0 > SM lid: 0 > Capability mask: 0x02510a68 > Port GUID: 0x0002c90200283736 > CA 'mthca1' > CA type: MT25208 (MT23108 compat mode) > Number of ports: 2 > Firmware version: 4.8.200 > Hardware version: 20 > Node GUID: 0x0002c90200283730 > System image GUID: 0x0002c90200283733 > Port 1: > State: Initializing > Physical state: LinkUp > Rate: 20 > Base lid: 0 > LMC: 0 > SM lid: 0 > Capability mask: 0x02510a68 > Port GUID: 0x0002c90200283731 > Port 2: > State: Active > Physical state: LinkUp > Rate: 20 > Base lid: 3 > LMC: 0 > SM lid: 1 > Capability mask: 0x02510a68 > Port GUID: 0x0002c90200283732 > -------------------------------------------------------------------------------------------------------------------------------------- > > Even ibibnetdiscover is detecting one hope. > So there is nothing wrong if I try to test 2 HCA connected back to back. > > Please tell me what can be done for running ib tests. > > Thanks, > SGM > _______________________________________________ > general mailing list > general@lists.openfabrics.org > http://*lists.openfabrics.org/cgi-bin/mailman/listinfo/general > > To unsubscribe, please visit > http://*openib.org/mailman/listinfo/openib-general > _______________________________________________ > general mailing list > general@lists.openfabrics.org > http://*lists.openfabrics.org/cgi-bin/mailman/listinfo/general > > To unsubscribe, please visit > http://*openib.org/mailman/listinfo/openib-general > -- Ira Weiny Math Programmer/Computer Scientist Lawrence Livermore National Lab 925-423-8008 wei...@llnl.gov _______________________________________________ general mailing list general@lists.openfabrics.org http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general