Hi folks, I continued installing Gentoo 1.4 and encountered following difficulty
(Remark: -Prompt - use "gentoo md" -disk partition on drive connected to bus0 only - without problem -creating filesystems - without complaint -mounting partitions - without complaint) Now when came to - stages tarballs and chroot (2 CD version) -Extraction of tarballs - stage2 - without complaint cdimage gentoo # mount -t proc proc /mnt/gentoo/proc (without complaint) cdimage gentoo # cp /etc/resolv.conf /mnt/gentoo/etc/resolv.conf (without complaint) cdimage gentoo # chroot /mnt/gentoo /bin/bash Illegal instruction I could not proceed further. Kindly advise. Thanks in advance. B.Regards Stephen On Fri, 2003-09-05 at 17:46, William Kenworthy wrote: > There's a driver for the 680 in 2.4.22-gss (one setting for udma, and > one for the ideraid) that I am using in IDE mode. Much better than the > 2.4.20 gentoo-sources for this card. Only prob is the card only has a > cdrom on it, and I dont have a /dev/hda, but there is a /proc/ide/hda > ... > > > > BillK > > > On Fri, 2003-09-05 at 11:28, Stephen Liu wrote: > > Hi Kai, > > > > Thanks for your response. > > > > I tried hard to search silraid driver on Internet without result > > including subscribing to "linux-kernel" mailing list, a very high > > traffic list. > > > > I found Arjan's driver working on Medley software RAID (Silicon Image > > 3112 SATARaid, CMD680) but I have no idea whether it works on Z-Cyber > > ATA133 RAID controller. I am still searching its download website. > > > > B.R. > > Stephen > > > > On Tue, 2003-09-02 at 23:57, Kai Lindenberg wrote: > > > Hi Stephen, > > > > > > Am Dienstag, 2. September 2003 17:31 schrieb Stephen Liu: > > > > This is my first time installing Gentoo. > > > > > > > > Hardware Config. > > > > RAID-0 (Z-Cyber ATA133 RAID) > > > > Drive-A: Connected to 1st slot of RAID controller > > > > Drive-B: Connected to 2nd slot of RAID controller > > > > > > [...] > > > > > > > I did following steps; > > > > 1)Booting up the PC with CD#1 > > > > 2)At prompt > > > > # gentoo md > > > > cdimage root# fdisk -l > > > > > > > > Disk /dev/ide/host0/bus1/target0/lun0/disc: 40.0 GB > > > > > > [...] > > > > > > > Disk /dev/ide/host0/bus0/target0/lun0/disc: 40.0 GB > > > > > > [...] > > > > > > > Why it is not a single hard drive, instead 2 drives being seen. > > > > One drive is of Linux system and another Win95 FAT32 (LBA) > > > > system. > > > > > > > > > Hey, you answered this question by yourself.... > > > > > > 1. This is not a "real" hardware raidcontroller, so you always see > > > all connected drives, maybe the windows driver hides them. > > > > > > 2. You don't see an additional "drive" because you have no module > > > for the linux kernel. Try to find a silraid driver patch for your > > > kernel, maybe the latest vanilla kernel supports it, the latest > > > stable 2.4.20-gentoo-r6 doesn't. > > > > > > Kai > > > > > > To Get Your Own iCareHK.com Email Address? Go To www.iCareHK.com. > > > > -- > > [EMAIL PROTECTED] mailing list -- [EMAIL PROTECTED] mailing list
