On 24 July 2006 00:52, Nick Rout wrote: > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.4 (tagged release) loading > ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) > ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low) > -> IRQ 10 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) > **********cx25840 0-0044: loaded v4l-cx25840.fw firmware (14264 bytes) > ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] > tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] > tveeprom 0-0050: The eeprom says no radio is present, but the tuner type > tveeprom 0-0050: indicates otherwise. I will assume that radio is present. > tveeprom 0-0050: Hauppauge model 26559, rev C260, serial# 2945285 > tveeprom 0-0050: tuner model is LG S001D MK3 (idx 60, type 38) > tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom > 0x74) tveeprom 0-0050: audio processor is CX25843 (idx 37) > tveeprom 0-0050: decoder processor is CX25843 (idx 30) > tveeprom 0-0050: has radio, has no IR remote > *************ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02050032 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) ivtv0: Create encoder radio stream > tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) > ivtv0: Initialized WinTV PVR 150, card #0 > ivtv: ==================== END INIT IVTV ====================
Mine looks pretty much the same except that it detects the remote. Firmware gets loaded, all drivers get loaded, no errors. Meanwhile I do have audio but very very faint if i raise everything to maximum (mixer, speaker amplifier, ivtvctl). I don't know. Maybe the hardware is fried. Uwe -- Mark Twain: I rather decline two drinks than a German adjective. http://www.SysEx.com.na -- [email protected] mailing list
