Hi Conxi, If you have a look in the Support Centre on https://my.geosoft.com , you should find a number of resources related to digitizing.
There is one in particular that I think you may find helpful: http://updates.geosoft.com/downloads/files/how-to-guides/Oasis_montaj_Target_Digitize_Interpretations.pdf The thing to remember for digitizing to a geostring file for Wireframing purposes, is that you can digitize on any map that is properly oriented in 3D. The how to guide describes using section maps with the drillhole extension, however any 3D section or plan map will work, you don't have to start with drillhole data. If you don't have drillhole data, the only thing you won't be able to do is snap to true drillhole locations. All of your digitizations will be found on the centre plane of your map. I hope that helps. If you are still in doubt, please feel free to send me your section maps, and I can see if they are properly oriented in 3D space or not and make suggestions on how to fix them if needed. Thanks, Becky Bodger Senior Technical Support Representative | Geosoft geosoft.com | blog | twitter | linkedIn | facebook | T +1 416.369.0111 #313 44% of explorers responded that, “data management is of critical importance”. Download the 2013 Exploration Information Management Survey -----Original Message----- From: Conxi <[email protected]> [mailto:[email protected]] Sent: November-10-14 11:08 AM To: Geosoft Oasis montaj and Target Subject: Re: [geonet] How to "digitize" a geological section Jim, thanks for your message! I have seen the video. But I do not have drillholes to interpret and then create a wireframe, I have 2D models from GMSYS. I am afraid it is not clear to me how to create the wireframe from the horizons of these models. BR, C James Degnan <[email protected]> writes: > Hi Conxi, > I found this video helpful: > http://www.geosoft.com/resources/video/geosoft-3d-geological-subsurfac > e-modelling/ I'd like to be able to create 3D bodies with intersecting > cross sections as well, but the software seems to only support > parallel cross section wire framing. > Good luck, > Jim > > James Degnan, P.G. > USGS New England Water Science > 331 Commerce Way, Suite 2 > Pembroke NH 03275 > http://nh.water.usgs.gov/ > [email protected] <[email protected]> > https://profile.usgs.gov/jrdegnan > 603-226-7826 (desk) > 603-568-8917 (cell) > > > On Mon, Nov 10, 2014 at 8:27 AM, Conxi <[email protected]> < > [email protected]> wrote: > >> Hi! >> >> I have a series of parallel cross sections and I would like to >> digitize them in order to create different surfaces as input for a 3D >> model. >> >> I have been looking into the documentation on the geosoft web page, >> but I haven't found what I was looking for, so any help will be welcome. >> >> Thanks, >> >> Conxi >> >> ______________________________ >> >> Dra. Conxi Ayala >> IGME >> Departamento de Investigación y Prospectiva Área de Geología del >> Subsuelo y Almacenamiento Geológico Geofísica >> email: [email protected] >> _______________________ >> >> www.igme.es >> >> --- >> >> Forum archives can be accessed here: >> http://lyris.geosoft.com/read/?fourm=geonet >> You are currently subscribed to geonet as: [email protected]. >> To subscribe or unsubscribe from any of our forums, select the User >> Forum selection on the Geosoft Community page: >> http://www.geosoft.com/support/community >> >> > > --- > > Forum archives can be accessed here: > http://lyris.geosoft.com/read/?fourm=geonet > You are currently subscribed to geonet as: [email protected]. > To subscribe or unsubscribe from any of our forums, select the User > Forum selection on the Geosoft Community page: > http://www.geosoft.com/support/community ______________________________ Dra. Conxi Ayala IGME Departamento de Investigación y Prospectiva Área de Geología del Subsuelo y Almacenamiento Geológico Geofísica email: [email protected] _______________________ www.igme.es --- Forum archives can be accessed here: http://lyris.geosoft.com/read/?fourm=geonet You are currently subscribed to geonet as: [email protected]. To subscribe or unsubscribe from any of our forums, select the User Forum selection on the Geosoft Community page: http://www.geosoft.com/support/community --- Forum archives can be accessed here: http://lyris.geosoft.com/read/?fourm=geonet You are currently subscribed to geonet as: [email protected]. To subscribe or unsubscribe from any of our forums, select the User Forum selection on the Geosoft Community page: http://www.geosoft.com/support/community
