Hi,
On Fri, May 8, 2009 at 5:01 PM, Justin Deoliveira <[email protected]>wrote:
> Right, after looking at the commits I noticed this was the case, which is
> sort of a special case.
>
> As per your comment:
>
> >From [1] I see that the response should contain some info
> > about the newly created resource.
>
> Where exactly is this. I read the specification of the PUT method and did
> not see such a reference.
Is the paragraph 10.2.2 - 201 Created
Daniele
>
>
> -Justin
>
>
>
> Daniele Romagnoli wrote:
>
>> Hi Justin,
>> I'm talking about the CoverageStoreFileResource which allows to add a new
>> coverage using the following syntax with PUT:
>> /workspaces/<ws>/coveragestores/<cs>/file[.<extension>]
>>
>> I have noticed that when done, it returns a STATUS_CREATED in the
>> response.
>>
>> Daniele
>>
>>
>> On Fri, May 8, 2009 at 3:55 PM, Justin Deoliveira
>> <[email protected]<mailto:
>> [email protected]>> wrote:
>>
>> hi Daniele,
>>
>> Where exaclty is a 201 being set as the response code for a PUT. The
>> semantic we are following for restconfig is to have PUT only be used
>> to modify existing resources, therefore only returning a 200.
>>
>> POST being used to create new resources on the other hand does
>> return a 201.. And it sets the Location header in the response,
>> pointing at the newly created resource. If you look at
>> ReflectiveResource.handlePost() you will see what I mean.
>>
>> That said, we could use PUT to allow for creation of resoures, it is
>> perfectly valid with regard to HTTP. What is your use case here?
>>
>> -Justin
>>
>> Daniele Romagnoli wrote:
>>
>> Hi list,
>> I'm doing some work on improving restconfig.
>> When putting some resource via rest in geoserver, in case
>> everything goes ok, you will receive a response with a return
>> code = 201 --> handlePut does this: getResponse().setStatus(
>> Status.SUCCESS_CREATED );
>> >From [1] I see that the response should contain some info
>> about the newly created resource.
>> This can be achieved by properly setting an Entity in the
>> response, before setting Status.SUCCESS_CREATED.
>> Actually, geoserver simply set CREATED in the response without
>> any additional info. Therefore, there isn't any information
>> about the just added layer.
>> Which type of information should we provide within the response?
>>
>> Any feedback is welcome.
>> Regards,
>> Daniele
>>
>> [1]: http://www.w3.org/Protocols/rfc2616/rfc2616-sec10.html
>>
>> -- -------------------------------------------------------
>> Eng. Daniele Romagnoli
>> Software Engineer
>>
>> GeoSolutions S.A.S.
>> Via Carignoni 51
>> 55041 Camaiore (LU)
>> Italy
>>
>> phone: +39 0584983027
>> fax: +39 0584983027
>> mob: +39 328 0559267
>>
>>
>> http://www.geo-solutions.it
>>
>> -------------------------------------------------------
>>
>>
>>
>> ------------------------------------------------------------------------
>>
>>
>>
>>
>> ------------------------------------------------------------------------------
>> The NEW KODAK i700 Series Scanners deliver under ANY
>> circumstances! Your
>> production scanning environment may not be a perfect world - but
>> thanks to
>> Kodak, there's a perfect scanner to get the job done! With the
>> NEW KODAK i700
>> Series Scanner you'll get full speed at 300 dpi even with all
>> image processing features enabled. http://p.sf.net/sfu/kodak-com
>>
>>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> Geoserver-devel mailing list
>> [email protected]
>> <mailto:[email protected]>
>> https://lists.sourceforge.net/lists/listinfo/geoserver-devel
>>
>>
>>
>> -- Justin Deoliveira
>> OpenGeo - http://opengeo.org
>> Enterprise support for open source geospatial.
>>
>>
>>
>>
>> --
>> -------------------------------------------------------
>> Eng. Daniele Romagnoli
>> Software Engineer
>>
>> GeoSolutions S.A.S.
>> Via Carignoni 51
>> 55041 Camaiore (LU)
>> Italy
>>
>> phone: +39 0584983027
>> fax: +39 0584983027
>> mob: +39 328 0559267
>>
>>
>> http://www.geo-solutions.it
>>
>> -------------------------------------------------------
>>
>>
>
> --
> Justin Deoliveira
> OpenGeo - http://opengeo.org
> Enterprise support for open source geospatial.
>
>
--
-------------------------------------------------------
Eng. Daniele Romagnoli
Software Engineer
GeoSolutions S.A.S.
Via Carignoni 51
55041 Camaiore (LU)
Italy
phone: +39 0584983027
fax: +39 0584983027
mob: +39 328 0559267
http://www.geo-solutions.it
-------------------------------------------------------
------------------------------------------------------------------------------
The NEW KODAK i700 Series Scanners deliver under ANY circumstances! Your
production scanning environment may not be a perfect world - but thanks to
Kodak, there's a perfect scanner to get the job done! With the NEW KODAK i700
Series Scanner you'll get full speed at 300 dpi even with all image
processing features enabled. http://p.sf.net/sfu/kodak-com
_______________________________________________
Geoserver-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/geoserver-devel
