Kavyashree M wrote:
Sir,
I am sorry I did not get any mail for that query since I posted it.
So I had to ask once again..
1. g_energy -f ener.edr -o box.xvg
selecting 15 16 17 0
2. gmxcheck -e ener.edr
Opened ener.edr as single precision energy file
frame: 0 (index 0), t: 0.000
Last energy frame read 50000 time 100000.000
Found 50001 frames with a timestep of 2 ps.
3. Gromacs version 4.5.3
This is the same data where I was mentioning that I
was getting "not a number" (nan) error for all
energy calculations under RMSD section.
I've said several times before that this energy file is probably junk, and again
I'd suspect that. The only thing to check would be to run gmxdump on the .edr
file (and redirect into some output file or pipe the output through "more" to
actually see it) and see where the energy values go screwy. If you find a bunch
of nonsensical information, then you have your answer.
-Justin
Thank you fro answering.
With Regards
M. Kavyashree
On Fri, Jun 24, 2011 at 4:57 PM, Justin A. Lemkul <[email protected]
<mailto:[email protected]>> wrote:
Kavyashree M wrote:
Dear users,
Any suggestions?
You haven't provided nearly enough diagnostic information for anyone
to offer you any useful help (as Mark said yesterday). For example,
please provide:
1. Your exact g_energy command line
2. The output of gmxcheck for this .edr file
3. Your Gromacs version
-Justin
Thank you
M. Kavyashree
On Thu, Jun 23, 2011 at 10:38 AM, Kavyashree M
<[email protected] <mailto:[email protected]>
<mailto:[email protected] <mailto:[email protected]>>> wrote:
Dear users,
In one of the simulations while calculating box dimensions
using g_energy this output was obtained -
Statistics over 50000001 steps [ 0.0000 through 100000.0000
ps ], 3
data sets
All statistics are over 1978700 points
Energy Average Err.Est. RMSD
Tot-Drift
------------------------------__------------------------------__-------------------
Box-X 0.0453229 1.8 0.637535
-9.93022 (nm)
Box-Y 0.0453229 1.8 0.637535
-9.93022 (nm)
Box-Z 0.0320482 1.3 0.450805
-7.02173 (nm)
but the dimensions of the box is different. plot attached.
I am not able to figure out why only 1978700 data point are
considered.
Kindly give some suggestions.
Thank you
with regards
M.Kavyashree
--
==============================__==========
Justin A. Lemkul
Ph.D. Candidate
ICTAS Doctoral Scholar
MILES-IGERT Trainee
Department of Biochemistry
Virginia Tech
Blacksburg, VA
jalemkul[at]vt.edu <http://vt.edu> | (540) 231-9080
http://www.bevanlab.biochem.__vt.edu/Pages/Personal/justin
<http://www.bevanlab.biochem.vt.edu/Pages/Personal/justin>
==============================__==========
--
gmx-users mailing list [email protected]
<mailto:[email protected]>
http://lists.gromacs.org/__mailman/listinfo/gmx-users
<http://lists.gromacs.org/mailman/listinfo/gmx-users>
Please search the archive at
http://www.gromacs.org/__Support/Mailing_Lists/Search
<http://www.gromacs.org/Support/Mailing_Lists/Search> before posting!
Please don't post (un)subscribe requests to the list. Use the www
interface or send it to [email protected]
<mailto:[email protected]>.
Can't post? Read http://www.gromacs.org/__Support/Mailing_Lists
<http://www.gromacs.org/Support/Mailing_Lists>
--
========================================
Justin A. Lemkul
Ph.D. Candidate
ICTAS Doctoral Scholar
MILES-IGERT Trainee
Department of Biochemistry
Virginia Tech
Blacksburg, VA
jalemkul[at]vt.edu | (540) 231-9080
http://www.bevanlab.biochem.vt.edu/Pages/Personal/justin
========================================
--
gmx-users mailing list [email protected]
http://lists.gromacs.org/mailman/listinfo/gmx-users
Please search the archive at
http://www.gromacs.org/Support/Mailing_Lists/Search before posting!
Please don't post (un)subscribe requests to the list. Use the
www interface or send it to [email protected].
Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
