Thanks viosose, I liked the way you developed your system, but there were a couple of things that were different between our systems. Your's works on a completely square grid system using an interval to calculate the dimension of the grid. I wanted the user to be able to just dictate the number of division instead of a specific distance allowing them to use a non-uniform grid pattern (although the two methods are basically interchangable). But I did really like how you solved the notching problem, so I re-wrote my definition to use a similar method and it worked great. I ultimately wanted a single curve and not the solid extrusion so that the curves could be output to a lasercutter, so I added a few steps to get the final curve result. I also added a label function so that you could keep the number of struts organized. I think this definition is now done, and I'll post the final version on my website http://www.liftarchitects.com. I've also posted 2 screenshots of the definition and the grasshopper definition here: Source Files: Screen Shot 1: http://grasshopper3d.googlegroups.com/web/waffle+system_full+shot.jpg?hl=en&gda=HeKf200AAABldvTupClBBQRPKkY0ld_Q0ArYIkJ3-e_tgE0RzJkmqkXs4C2jAT3Q0mkcfUCXsXBJROYwIvG-GNlrkyFBYFff5Tb_vjspK02CR95VRrtmeQ&gsc=0pYe5gsAAABuDHiwh-5CddGVjWhz4FU5 Screen Shot2: http://grasshopper3d.googlegroups.com/web/waffle+system_detail.jpg?hl=en&gda=DHt7okoAAABldvTupClBBQRPKkY0ld_Q0ArYIkJ3-e_tgE0RzJkmqpG0p4oGWW9Ex1IZ0JEYJBcDdML5KEYLI3CzILF8CcXL_e3Wg0GnqfdKOwDqUih1tA&gsc=0pYe5gsAAABuDHiwh-5CddGVjWhz4FU5 Grasshopper Definition: http://grasshopper3d.googlegroups.com/web/waffle+system_10.ghx?hl=en&gda=LVHQhUYAAABldvTupClBBQRPKkY0ld_Q0ArYIkJ3-e_tgE0RzJkmqnYuWcwjW6kCVQ8ttgzl5au9RDn0rs_1yuNedF3EkhHjE-Ea7GxYMt0t6nY0uV5FIQ&gsc=0pYe5gsAAABuDHiwh-5CddGVjWhz4FU5 Thanks for your help. Best, Andy
On Oct 24, 12:35 pm, visose <[EMAIL PROTECTED]> wrote: > Since you mentioned it's for laser cutting, I added some components > that place the beam outlines neatly in the ground > plane:http://grasshopper3d.googlegroups.com/web/projectbeams(2).jpg > Btw, ignore the previous comment. The slope happens perpendicular to > the outline of the beams. Since the objective is to achieve only the > outline of the beams, this is not a problem. > > On Oct 24, 8:25 pm, visose <[EMAIL PROTECTED]> wrote: > > > Btw, i don't think the method i used to create the notches is the most > > appropriate since bottom of the opening will have the same slope as > > the top of the crossing beam so they won't fit tightly. > > > On Oct 24, 7:50 pm, visose <[EMAIL PROTECTED]> wrote: > > > > It's true, the boolean difference doesn't work with extruded surfaces. > > > I created a boolean difference script with the VB.NET component and > > > also doesn't work, so the problem may be either from the boolean > > > difference sdk (which i doubt) or from the extruded surface component. > > > I couldn't find an example of how to script a extruded surface in the > > > wiki. > > > > Nevertheless, I recreated a definition of what I think you are trying > > > to achieve without extruding a surface. Maybe It will help > > > you.http://grasshopper3d.googlegroups.com/web/woodframe.jpghttp://grassho... > > > > On Oct 24, 4:54 pm, Rchitekt <[EMAIL PROTECTED]> wrote: > > > > > Thanks. I'm still unsure why the boolean difference isn't working on > > > > this file. I made a separate file where I had a cube and a shpere as > > > > two Breps... and then I used the Boolean Difference to "trim" out one > > > > from the other, and it works like you think it would. Only, when I > > > > try that in this file, it doesn't seem to work. I've been extruding a > > > > planar surface to give me a closed Brep. Both the Notches and the > > > > extruded struts show that they are closed Breps, and yet when I use > > > > the Boolean Difference component, all that I get is a empty Brep set > > > > as a result. Any ideas? > > > > Thanks, > > > > Andy > > > > > On Oct 24, 12:36 am, David Rutten <[EMAIL PROTECTED]> wrote: > > > > > > Hi Andy, > > > > > > trimming is always a bit more tricky, if only because it's not clear > > > > > which remaining parts you want to keep. If you're trimming a single > > > > > surface with a closed loop, it's not ambiguous, but otherwise... > > > > > > I'll look into adding a bunch of trimming components, for I doubt that > > > > > one will do the trick. > > > > > > -- > > > > > David Rutten > > > > > Robert McNeel & Associates > > > > > > On Oct 24, 1:23 am, Rchitekt <[EMAIL PROTECTED]> wrote: > > > > > > > David, > > > > > > I see that there is an "Untrim" surface component in the last > > > > > > install, > > > > > > but is there a trim command that I could use in this case? Would it > > > > > > be something that will be released in the new version? Or should I > > > > > > try to make some sort of work around? > > > > > > Thanks, > > > > > > Andy > > > > > > > On Oct 23, 1:18 pm, Rchitekt <[EMAIL PROTECTED]> wrote: > > > > > > > > I've been working on a waffle system that creates an "egg crate" > > > > > > > structure from any set surface in Rhino. It has parametric > > > > > > > sliders to > > > > > > > control how far you want to extrude the surface, the number of > > > > > > > divisions in the x and y axis and the material thickness of the > > > > > > > actual > > > > > > > struts. Ideally, this definition would be used to create laser > > > > > > > cut > > > > > > > models of any surface, and the notches would be already put into > > > > > > > each > > > > > > > strut. I'm having one small problem. I've generated the boundary > > > > > > > curves (the strut outline) and I've been able to create the > > > > > > > notches > > > > > > > based on the material thickness. My problem is I can't seem to > > > > > > > join > > > > > > > the two... meaning, I can't seem to trim out the notch portion of > > > > > > > the > > > > > > > boundary curve and get one unified curve that could be immediately > > > > > > > sent to the laser cutter. I've tried to create solids out of the > > > > > > > struts and the notches and doing a boolean difference, but it > > > > > > > didn't > > > > > > > seem to give me any kind of usable output. I'm very close to > > > > > > > finishing this script and I'm just curious if anyone could help > > > > > > > me on > > > > > > > this last step. Here's a link to the screenshot of how the script > > > > > > > workshttp://grasshopper3d.googlegroups.com/web/waffle%20system_01.jpg?hl=en > > > > > > > And here is a link to the > > > > > > > definition.http://groups.google.com/group/grasshopper3d/web/waffle%20system_08.g... > > > > > > > Thanks for your help in advance. > > > > > > > Best, > > > > > > > Andy
