Hi, I am not sure, but here is my try:
I cloned your channel2 repo, and saw in emacs-hide-comnt.scm: (define-module (gnu packages emacs-hide-comnt) Modules names in Guile (in all schemes ?) must match the path, so either put emacs-hide-comnt.scm in gnu/packages, or change the above line to: (define-module (emacs-hide-comnt) See that urweb.scm starts with: (define-module (urweb) My interpretation is that the error message means that the emacs-hide-comnt module was not found where it was looked for, i.e. in gnu/packages. This may not be the only problem, but it is worth a try. Good luck :) Cheers, Edouard. Andreas Reuleaux <[email protected]> writes: > Hi, > > I am trying to set up my own channel for some personal packages, > and I do have some success to that end, but I am still experiencing > issues: > > > TL;dr - short summary: > > my package: emacs-hide-comnt.scm (below) breaks my setup for "guix pull" > (which otherwise works just fine without that package) > my package emacs-hide-comnt.scm cannot be too bad either: > I can build+install it just fine by hand. > > > > I am following the guix guide, and have stolen two packages from > > --8<---------------cut here---------------start------------->8--- > https://github.com/jsoo1/guix-channel > --8<---------------cut here---------------end--------------->8--- > > > namely emacs-dump.scm (which provides my-emacs-dump), and > urweb.scm. > > I have set up my own git repo (with just these two packages for now) at: > > --8<---------------cut here---------------start------------->8--- > http://git.a-rx.info/channel > --8<---------------cut here---------------end--------------->8--- > > > and (with a git-url) in my ~/.config/guix/channels.scm: > > --8<---------------cut here---------------start------------->8--- > (cons (channel > (name 'my-stuff) > > > (url "git://git.a-rx.info/channel") > > (introduction > (make-channel-introduction > "56384c65b5d57606cd7ff3e2a4db1c99c24d7adf" > (openpgp-fingerprint > "99BB E77D 73AE 07B9 D4B0 CA2E 3384 11E5 6E09 31B5") > )) > > ) > %default-channels) > --8<---------------cut here---------------end--------------->8--- > > > > I can "guix pull" (I am using "--allow-downgrades" the first time here, as I > have used > channel my-stuff with a different inital commit before), anyway this > works fine so far - guix pull does not complain about the my-stuff channel. > > --8<---------------cut here---------------start------------->8--- > rx@dell ~$ guix pull --allow-downgrades > Updating channel 'my-stuff' from Git repository at > 'git://git.a-rx.info/channel'... > guix pull: warning: moving channel 'my-stuff' from > 12ac4ab75c0b9dc247af3a65179c566e198d908d to unrelated commit > 56384c65b5d57606cd7ff3e2a4db1c99c24d7adf > Updating channel 'guix' from Git repository at > 'https://git.savannah.gnu.org/git/guix.git'... > Building from these channels: > guix https://git.savannah.gnu.org/git/guix.git 63fec9f > my-stuff git://git.a-rx.info/channel 56384c6 > Computing Guix derivation for 'x86_64-linux'... / > substitute: updating substitutes from 'https://ci.guix.gnu.org'... 100.0% > substitute: updating substitutes from 'https://bordeaux.guix.gnu.org'... > 100.0% > The following derivations will be built: > /gnu/store/dsb3bcmddgsvn34wxh0g2mbm4lyq1haz-profile.drv > /gnu/store/d227lqkghmg48b34b81si8hdmz3vba64-my-stuff.drv > /gnu/store/mcp30c79gi9cdnckg4ghahkaygn85ykk-inferior-script.scm.drv > /gnu/store/d84yrjgr6bkg7c6h9i0bxjz7cfxhisp2-profile.drv > /gnu/store/vrr8flhvf06xprqm6n9q45pj10h7r10g-inferior-script.scm.drv > > building > /gnu/store/mcp30c79gi9cdnckg4ghahkaygn85ykk-inferior-script.scm.drv... > building /gnu/store/d227lqkghmg48b34b81si8hdmz3vba64-my-stuff.drv... > building CA certificate bundle... > listing Emacs sub-directories... > building fonts directory... > building directory of Info manuals... > building database for manual pages... > building profile with 2 packages... > building > /gnu/store/vrr8flhvf06xprqm6n9q45pj10h7r10g-inferior-script.scm.drv... > building package cache... > building profile with 2 packages... > New in this revision: > 2 new packages: lsofgraph, urweb > > rx@dell ~$ guix pull > Updating channel 'my-stuff' from Git repository at > 'git://git.a-rx.info/channel'... > Updating channel 'guix' from Git repository at > 'https://git.savannah.gnu.org/git/guix.git'... > Building from these channels: > guix https://git.savannah.gnu.org/git/guix.git 63fec9f > my-stuff git://git.a-rx.info/channel 56384c6 > Computing Guix derivation for 'x86_64-linux'... / > nothing to be done > > rx@dell ~$ > --8<---------------cut here---------------end--------------->8--- > > > and "urweb" is available, for example > > --8<---------------cut here---------------start------------->8--- > rx@dell ~$ guix package -A urwe > urweb 20190217 out urweb.scm:15:2 > rx@dell ~ > --8<---------------cut here---------------end--------------->8--- > > > > > Thus apparently my setup is not too bad (including my rx.key in the > keyring branch etc.). > > > Now I am setting up a second channel2 instead: again with the two packages > emacs-dump.scm and urweb.scm as above, but additionally an emacs package > that I have created myself: emacs-hide-comnt.scm > > (Really this is just a prerequisite for another package that I am > interested in, and I have a package definition for as well: > emacs-thing-cmds.scm - but I keep that question for another mail): > > Now with my ~/.config/guix/channels.scm for channel2: > > --8<---------------cut here---------------start------------->8--- > (cons (channel > (name 'my-stuff2) > > > (url "git://git.a-rx.info/channel2") > > (introduction > (make-channel-introduction > "3a64194919ceeb16ee03df17de2c3c612d410145" > (openpgp-fingerprint > "99BB E77D 73AE 07B9 D4B0 CA2E 3384 11E5 6E09 31B5") > )) > > ) > %default-channels) > --8<---------------cut here---------------end--------------->8--- > > > > I cannot pull any more: > > --8<---------------cut here---------------start------------->8--- > rx@dell ~$ guix pull > Updating channel 'my-stuff2' from Git repository at > 'git://git.a-rx.info/channel2'... > Updating channel 'guix' from Git repository at > 'https://git.savannah.gnu.org/git/guix.git'... > Building from these channels: > guix https://git.savannah.gnu.org/git/guix.git 63fec9f > my-stuff2 git://git.a-rx.info/channel2 3a64194 > Computing Guix derivation for 'x86_64-linux'... - > substitute: updating substitutes from 'https://ci.guix.gnu.org'... 100.0% > substitute: updating substitutes from 'https://bordeaux.guix.gnu.org'... > 100.0% > The following derivations will be built: > /gnu/store/1vvwqnj7d1hp8nf8kcpf1r5wrlibkxya-profile.drv > /gnu/store/hiqych1a0qdmdzq45mi1k96df9zr0p7k-my-stuff2.drv > /gnu/store/b0hk5dvfid7pkjxrwfylmkn5w3pwzbxq-inferior-script.scm.drv > /gnu/store/5ww6yaqz98jnkp2gfdpjzksx5azwd63i-inferior-script.scm.drv > /gnu/store/j9w5gvf7slfc1ahmryd45i0nfr3j8509-profile.drv > > building > /gnu/store/b0hk5dvfid7pkjxrwfylmkn5w3pwzbxq-inferior-script.scm.drv... > building /gnu/store/hiqych1a0qdmdzq45mi1k96df9zr0p7k-my-stuff2.drv... > |builder for `/gnu/store/hiqych1a0qdmdzq45mi1k96df9zr0p7k-my-stuff2.drv' > failed to produce output path > `/gnu/store/ww01v7zdx110q887146y9m67j3rikypw-my-stuff2' > build of /gnu/store/hiqych1a0qdmdzq45mi1k96df9zr0p7k-my-stuff2.drv failed > View build log at > '/var/log/guix/drvs/hi/qych1a0qdmdzq45mi1k96df9zr0p7k-my-stuff2.drv.bz2'. > cannot build derivation > `/gnu/store/1vvwqnj7d1hp8nf8kcpf1r5wrlibkxya-profile.drv': 1 dependencies > couldn't be built > guix pull: error: build of > `/gnu/store/1vvwqnj7d1hp8nf8kcpf1r5wrlibkxya-profile.drv' failed > rx@dell ~$ > --8<---------------cut here---------------end--------------->8--- > > > with > > --8<---------------cut here---------------start------------->8--- > rx@dell ~$ bzcat > '/var/log/guix/drvs/hi/qych1a0qdmdzq45mi1k96df9zr0p7k-my-stuff2.drv.bz2' > (repl-version 0 1 1) > (exception misc-error (value #f) (value "no code for module ~S") (value > ((emacs-hide-comnt))) (value #f)) > rx@dell ~$ > --8<---------------cut here---------------end--------------->8--- > > > > Apparently my emacs-hide-comnt.scm package > at http://git.a-rx.info/channel2/tree/ breaks my setup. > > And I don't see why: I can download the package and build/install it > just fine: > > --8<---------------cut here---------------start------------->8--- > rx@dell ~$ wget -nd http://git.a-rx.info/channel2/plain/emacs-hide-comnt.scm > --2021-08-28 16:46:47-- > http://git.a-rx.info/channel2/plain/emacs-hide-comnt.scm > Resolving git.a-rx.info (git.a-rx.info)... 178.79.166.98 > Connecting to git.a-rx.info (git.a-rx.info)|178.79.166.98|:80... connected. > HTTP request sent, awaiting response... 200 OK > Length: 2035 (2.0K) [text/plain] > Saving to: ‘emacs-hide-comnt.scm’ > > emacs-hide-comnt.scm > 100%[===============================================================>] > 1.99K --.-KB/s in 0s > > 2021-08-28 16:46:47 (324 MB/s) - ‘emacs-hide-comnt.scm’ saved [2035/2035] > > rx@dell ~$ > --8<---------------cut here---------------end--------------->8--- > > --8<---------------cut here---------------start------------->8--- > rx@dell ~$ guix build -f emacs-hide-comnt.scm > /gnu/store/w098p5vxd0iy31mxkcp47xk3n5f5d175-emacs-hide-comnt-2019.11 > rx@dell ~$ > rx@dell ~$ guix install $(guix build -f emacs-hide-comnt.scm) > The following package will be upgraded: > emacs-hide-comnt (dependencies or package changed) > > nothing to be done > rx@dell ~$ > --8<---------------cut here---------------end--------------->8--- > > > > Hm??? > > One difference that I see: my emacs-hide-comnt.scm has > a last line of > > --8<---------------cut here---------------start------------->8--- > emacs-hide-comnt > --8<---------------cut here---------------end--------------->8--- > > and I need that for building the package by hand - If I remove > that line (the corresponding packages: emacs-dump.scm, urweb.scm > don't have such last lines): then I cannot build my package by hand > any more - and worse: I still cannot pull from my channel2 ?? > > Thanks in advance.
