Hi Joel,
I also have twin HDS9980V subsystems with TrueCopy and ShadowImage
installed. I tried your ICKDSK JCL on using two of my 1 cylinder DASD volumes
( they are former XRC utility volumes ) and I believe I received the same error:
ICKDSF - MVS/ESA DEVICE SUPPORT FACILITIES 17.0
PPRCOPY ESTPAIR -
DDNAME(A) -
MODE(COPY) -
PRIMARY(X'992F',43323,X'3E') -
SECONDARY(X'992F',43323,X'3F') -
LSS(X'0F',X'0F')
ICK00700I DEVICE INFORMATION FOR 3F3E IS CURRENTLY AS FOLLOWS:
PHYSICAL DEVICE = 3390
STORAGE CONTROLLER = 2105
STORAGE CONTROL DESCRIPTOR = E8
DEVICE DESCRIPTOR = 0A
ADDITIONAL DEVICE INFORMATION = 4A000035
TRKS/CYL = 15, # PRIMARY CYLS = 1
ICK04000I DEVICE IS IN SIMPLEX STATE
ICK10710I I/O ERROR OCCURRED ON DEVICE 3F3E
CSW = 0EF038 0E000000 CCW = 270EF060 00000021
000EF060 + 00 62413E3F 0F00F0F0 F0F0F0F4 F3F3F2F3
000EF070 + 10 992F0F00 F0F0F0F0 F0F4F3F3 F2F3992F
000EF080 + 20 00
ICKDSF - MVS/ESA DEVICE SUPPORT FACILITIES 17.0
SENSE = 80000000 BE00000F 58000000 00000000 23124800 992F0F0F
000040C2 00000000
ICK34082I A COMMAND WAS RECEIVED THAT IS NOT VALID FOR THIS PPRC
STATE
ICK30003I FUNCTION TERMINATED. CONDITION CODE IS 12
ICK00002I ICKDSF PROCESSING COMPLETE. MAXIMUM CONDITION CODE WAS
12
I had the PPRC source volume, UCB address 3F3E and the PPRC target volume,
UCB address 3F3F online to all of my z/OS images. When I varied the PPRC
target volume offline ( as Ron Hawkins suggested ), the command worked:
ICKDSF - MVS/ESA DEVICE SUPPORT FACILITIES 17.0
PPRCOPY ESTPAIR -
DDNAME(A) -
MODE(COPY) -
PRIMARY(X'992F',43323,X'3E') -
SECONDARY(X'992F',43323,X'3F') -
LSS(X'0F',X'0F')
ICK00700I DEVICE INFORMATION FOR 3F3E IS CURRENTLY AS FOLLOWS:
PHYSICAL DEVICE = 3390
STORAGE CONTROLLER = 2105
STORAGE CONTROL DESCRIPTOR = E8
DEVICE DESCRIPTOR = 0A
ADDITIONAL DEVICE INFORMATION = 4A000035
TRKS/CYL = 15, # PRIMARY CYLS = 1
ICK04000I DEVICE IS IN SIMPLEX STATE
ICK02203I PPRCOPY ESTPAIR FUNCTION COMPLETED SUCCESSFULLY
ICK02231I DEVICE IS NOW A PEER TO PEER REMOTE COPY VOLUME
ICK00001I FUNCTION COMPLETED, HIGHEST CONDITION CODE WAS 0
I also received the following messages on each of my z/OS images, which I
normally receive whenever I start a PPRC pair on my system:
IEA494I 3F3E,SO3F3E,PPRC PAIR PENDING,SSID=992F,CCA=3E
IEA494I 3F3E,SO3F3E,PPRC PAIR FULL DUPLEX,SSID=992F,CCA=3E
HTH
Glenn Miller
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO
Search the archives at http://bama.ua.edu/archives/ibm-main.html
