Hi R'Shmuel AMV"SH,
I used Dick Thornton's Disassembler on File 234. It seemed to work.
I did not open an IBM ticket.
Thank you for the suggestions.
Regards,
David
On 2021-11-18 17:31, Seymour J Metz wrote:
Have you tried any of the disassemblers on the CBT tape> Have you reported the
error to IBM?
--
Shmuel (Seymour J.) Metz
https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fmason.gmu.edu%2F~smetz3&data=04%7C01%7C%7Cb63275a7094049b156f508d9aae349b9%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637728715517119460%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=0zAYtYa1bUHcQ24tkdK30tlvBWYlQfgXSFUWsqfQvsg%3D&reserved=0
________________________________________
From: IBM Mainframe Discussion List [IBM-MAIN@LISTSERV.UA.EDU] on behalf of
David Spiegel [dspiegel...@hotmail.com]
Sent: Thursday, November 18, 2021 9:20 AM
To: IBM-MAIN@LISTSERV.UA.EDU
Subject: Re: Disassembly/Reassembly
JMQ416A
On 2021-11-18 09:13, Seymour J Metz wrote:
It sounds as if the disassembler is not generating an EXTRN TSAUXWRK from the
ESD entry. Which disassembler are you using?
--
Shmuel (Seymour J.) Metz
https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fmason.gmu.edu%2F~smetz3&data=04%7C01%7C%7Cb63275a7094049b156f508d9aae349b9%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637728715517119460%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=0zAYtYa1bUHcQ24tkdK30tlvBWYlQfgXSFUWsqfQvsg%3D&reserved=0
________________________________________
From: IBM Mainframe Discussion List [IBM-MAIN@LISTSERV.UA.EDU] on behalf of
David Spiegel [dspiegel...@hotmail.com]
Sent: Wednesday, November 17, 2021 5:50 PM
To: IBM-MAIN@LISTSERV.UA.EDU
Subject: Disassembly/Reassembly
Hi,
I have been given a Load Module and source code.
The Source Code, however, does not 100% match the Disassembled Load Module.
This module has been running in production since 1994.
With that preface ...
I tried reassembling the disassembled module source and have a problem.
One instruction says:
L R2,=A(TSAUXWRK)
Later in the program, I see the following in the disassembled source
DC A(TSAUXWRK)
Yet, the definition of TSAUXWRK appears nowhere in the disassembled
source, causing a ASM044E.
I looked in the source provided and it has:
TSAUXWRK CSECT
in the middle of the program. (When I assemble this, even though it is
not the correct source, I get a clean assembly.)
Has anyone encountered anything like this (addressing a CSECT as an
A=CON works, but, only with original source)?
Is there a remedy for this?
Thanks and regards,
David
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
.
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
.
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
