Good afternoon, Tony!
I found the manual and opened Case TS016307677 - Connect:Direct - DGASACMP
Program Parameters: Can this program accept a parameter (QPL_FLAG_GZIP_MODE
flag) to add GZIP header and trailer information to the output stream (when
performing compression)?
If this is possible, then I and our customer will be able to unzip the file
with GZip.
Thank You and Please Be Safe.
Please Note: I would appreciate it if you would please include my teammates
("[email protected]") in future emails to keep them informed.
Len Sasso
Systems Administrator Senior
CSRA, A General Dynamics Information Technology Company
327 Columbia TPKE
Rensselaer, NY 12144
TEAM: Together Everyone Achieves More
Office Hours: M-F 7 AM - 3:30 PM
Out-Of-The-Office:
Cell: (518) 894-0879
Phone: (518) 257-4209
Fax: (518) 257-4300
[email protected]
URL: www.gdit.com
Customer Focused, Value Driven, Delivery Obsessed
________________________________________
From: IBM Mainframe Discussion List <[email protected]> on behalf of
Cieri, Anthony <[email protected]>
Sent: Thursday, May 23, 2024 12:45 PM
To: [email protected] <[email protected]>
Subject: Re: IBM Sterling Connect:Direct for z/OS Version 6, Release 2
This Message Is From an External Sender
Please use caution with links, attachments, and any requests for credentials.
Len,
Check out the following manual; IBM Connect:Direct for z/OS Version
6.1.....
On page 653 is an example of the Batch Compression utility (DGASACMP).
You can run this and then transfer the file............
Good Luck
Tony
-----Original Message-----
From: IBM Mainframe Discussion List <[email protected]> On Behalf Of
Sasso, Len
Sent: Thursday, May 23, 2024 7:48 AM
To: [email protected]
Subject: Re: IBM Sterling Connect:Direct for z/OS Version 6, Release 2
[[ SEI WARNING *** This email was sent from an external source. Do not open
attachments or click on links from unknown or suspicious senders. *** ]]
Good morning, Steve!
Could you please provide an example of running compression in a run task and
then sending the resulting file to the target system?
Or point me to a manual that provides an example?
Thank You and Please Be Safe.
Len Sasso
Systems Administrator Senior
CSRA, A General Dynamics Information Technology Company
327 Columbia TPKE
Rensselaer, NY 12144
TEAM: Together Everyone Achieves More
Office Hours: M-F 7 AM - 3:30 PM
Out-Of-The-Office:
Cell: (518) 894-0879
Phone: (518) 257-4209
Fax: (518) 257-4300
[email protected]
URL: www.gdit.com
Customer Focused, Value Driven, Delivery Obsessed
From: IBM Mainframe Discussion List <[email protected]> on behalf of
Steve Thompson <[email protected]>
Sent: Wednesday, May 22, 2024 6:01 PM
To: [email protected] <[email protected]>
Subject: Re: IBM Sterling Connect:Direct for z/OS Version 6, Release 2
This Message Is From an External Sender
Please use caution with links, attachments, and any requests for credentials.
Yes. You can either run compression in a run task, and then send the resulting
file to the target system, OR you can compress it via a z/OS job and then have
C:D pick up the resulting file and send it.
The receiving site, if they are going to use it, must know what you used for
compression.
When I was last working on C:D, there was a utility provided to do
compress/decompress in "batch". But one could also do the same with, say,
ADRDSSU.
Regards,
Steve Thompson
On 5/22/2024 10:12 AM, Sasso, Len wrote:
> Good morning!
>
> The Connect Direct set of cards below will compress the file during transfer
> to the destination and then extract the file at the destination.
>
> SIGNON CASE=YES
> SUBMIT PROC=COPYDISK &COMPRESS=COMPRESS -
> SNODE=SFGTST SNODEID=(ABCDE,123stu456) -
> &FROMDSN=ABC.FILE -
> &TODSN='/mailbox/TEST.FILE'
> SIGNOFF
>
> Is it possible to "tell" Connect Direct, not to extract the file at the
> destination?
> If so, how?
>
>
> Thank You and Please Be Safe.
>
> Len Sasso
> Systems Administrator Senior
> CSRA, A General Dynamics Information Technology Company
> 327 Columbia TPKE
> Rensselaer, NY 12144
>
> TEAM: Together Everyone Achieves More
>
>
> ----------------------------------------------------------------------
> For IBM-MAIN subscribe / signoff / archive access instructions, send
> email to [email protected] with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to
[email protected] with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to
[email protected] with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
