What errors are you seeing with the NETSRVx startup? Does NETSRVx have an OMVS Segment?
The HASP466 messages do not show a /* */ paring on the line statement. Is there a /* */? Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Jim Thomas > Sent: Saturday, February 01, 2014 8:13 AM > To: [email protected] > Subject: Re: JES2 / TCP/IP Network Printer Definitions.... > > Ma'am, > > Absolutely ... the socket definition (w/local values changed) was included but no > worries, I'll re-post. > > 'n' = numeric value. > > z/OS 1.13 ... > > SOCKET(socketn),CONNECT=YES, > IPADDR=1.2.3.4, > LINE=n, > NETSERV=n, > NODE=noden > > No ... I cannot get NETSRV to start either ... I'll paste the messages below the > SOCKET messages. > > $HASP466 PARMLIB STMT 205 SOCKET(socketn),CONNECT=YES, > $HASP466 PARMLIB STMT 205 /* 1/31 > $HASP466 PARMLIB STMT 205 /14 JIMT*/IPADDR=1.2.3. > $HASP466 PARMLIB STMT 205 4, /* 1/ > $HASP466 PARMLIB STMT 205 31/14 JIMT*/LINE=2, > $HASP466 PARMLIB STMT 205 /* > $HASP466 PARMLIB STMT 205 1/31/14 JIMT*/NETSERV=n, > $HASP466 PARMLIB STMT 205 /* > $HASP466 PARMLIB STMT 205 1/31/14 JIMT*/NODE=noden > $HASP466 PARMLIB STMT 205 /* > $HASP466 PARMLIB STMT 205 1/31/14 JIMT*/ > $HASP003 RC=(01),SOCKET(RICOSOK) - INVALID SYNTAX > 01 $HASP469 REPLY PARAMETER STATEMENT, CANCEL, OR END > > $SNETSRVn,SOCKET=socketn > $HASP003 RC=(104),S 865 > $HASP003 RC=(104),S NETSRVn SOCKET - SOCKET MUST SPECIFY LOCAL > $HASP003 NODE > > Kind Regards. > > Jim Thomas > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Lizette Koehler > Sent: Saturday, February 01, 2014 8:46 AM > To: [email protected] > Subject: Re: JES2 / TCP/IP Network Printer Definitions.... > > Could you provide the socket definition > Level of z/OS > And the complete error message? > > And any info from the NETSRV stc? > > Is the NetSrv STC up? > > > Thanks > > Lizette > > > -----Original Message----- > > From: IBM Mainframe Discussion List [mailto:[email protected]] > > On Behalf Of Jim Thomas > > Sent: Saturday, February 01, 2014 6:59 AM > > To: [email protected] > > Subject: Re : JES2 / TCP/IP Network Printer Definitions.... > > > > Hello, > > > > I'm trying to get a network printer to be useable (via tcp/ip) from JES2. > > > > LINE(n) UNIT=TCP, > > CONNECT=YES > > > > NODE(n) CONNECT=YES, > > LINE=n, > > NAME=noden > > > > SOCKET(socketn),CONNECT=YES, > > IPADDR=1.2.3.4, > > LINE=n, > > NETSERV=n, > > NODE=noden > > > > NETSRVn SOCKET=socketn > > > > DESTID(destidn) DEST=noden (I do not have a DESTDEF) > > > > > > JES2 startup gives me syntax errors on the SOCKET definition and I am > unable to > > get this 'connected' ... > > > > Any advice would be greatly appreciated. > > > > Kind Regards. > > > > Jim Thomas > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send email to > [email protected] with the message: INFO IBM-MAIN > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send email to > [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
