I guess I need to get some more understanding of what you are trying to connect to JES2 via TCPIP.
What is the type of network printer? Have you verified it can be done this way? The reasons I ask is VPS software is made to handle what JES2 cannot do natively. So I am just trying to verify this is something that JES2 can do. Next, Unless your RACF/SAF group has provided something like a Default UID, your NETSRVx will require an OMVS segment to do this. I have also found this APAR which may be helpful. It is very long and detailed on NETSRV OA19215: INCORRECT DOC FOR DEFINING NETSRV USERID TO OMVS http://www-01.ibm.com/support/docview.wss?uid=isg1OA19215 The Defining a NETSRV sub-section is contained within the the Special considerations for TCP/IP NJE section and should read: Special considerations for TCP/IP NJE Controlling TCP/IP NJE networking is similar to controlling SNA networking. In addition to VTAM, it is necessary to start TCP/IP in order to communicate using TCP/IP. TCP/IP NJE # configurations also require that a JES2 SOCKET statement be defined which specifies the IP address and port (typically 175 or 2252) that will be used by both the local node and the partner node. The IP address and port used by the local node # must then be specified on a SOCKET statement associated with # the NETSRV in order for JES2 to listen for TCP connections. | The sockets LOCAL and LOCALTLS are defined automatically by | JES2 initialization and default to listening on all IP addresses and TCP/IP stacks associated with the MVS image. For definitions regarding the partner node, it is necessary to know the IP name or address of the partner node, either as a | symbolic name (such as wash.ibm.com) or as an explicit address in either dotted decimal format (for IPv4) or hex-colon format (for IPv6). You can also increase security in your network by using SSL or TLS across this NJE link. | For more information, see Application Transparent - Transport Layer Security (AT-TLS) data protection in z/OS Communications Server: IP Configuration Guide. | Setting up TCP/IP Before implementing NJE/TCP, you need to set up TCP/IP on your MVS system. If you are already using TCP/IP for other applications, there are a few additional definitions required | to enable JES2 to perform NJE/TCP. Your security | administrator should determine the actual values to use for | the example below. For more information, see the z/OS | Security Server RACF Security Administrator's Guide and z/OS | UNIX System Services Planning documentation. # # Check the buffer sizes defined in your TCP/IP definitions. In particular, you must set the TCPCONFIG MAXRECVBUFRSIZE and RECVBUFRSIZE parameters to at least 512, and ideally set them to a value of 32768 or higher. The NJE/TCP implementation also supports virtual IP addresses (VIPA addresses), and the use of sysplex distributor to share IP addresses throughout a SYSPLEX. There is no additional JES2 setup to take advantage of either of these features other than to specify the appropriate IP address or host name on the SOCKET Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Jim Thomas > Sent: Saturday, February 01, 2014 10:18 AM > To: [email protected] > Subject: Re: Re : JES2 / TCP/IP Network Printer Definitions.... > > Sir, > > I've tried that too... it was when it failed (on the first go around), that I tried > NETSERV (per the doc). > > Kind Regards. > > Jim Thomas > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Bob Rutledge > Sent: Saturday, February 01, 2014 9:50 AM > To: [email protected] > Subject: Re: Re : JES2 / TCP/IP Network Printer Definitions.... > > Jim Thomas wrote: > > Hello, > > > > I'm trying to get a network printer to be useable (via tcp/ip) from JES2. > > > > LINE(n) UNIT=TCP, > > CONNECT=YES > > > > NODE(n) CONNECT=YES, > > LINE=n, > > NAME=noden > > > > SOCKET(socketn),CONNECT=YES, > > IPADDR=1.2.3.4, > > LINE=n, > > NETSERV=n, > > Should this not be NETSRV= ? > > > NODE=noden > > > > NETSRVn SOCKET=socketn > > > > DESTID(destidn) DEST=noden (I do not have a DESTDEF) > > > > > > JES2 startup gives me syntax errors on the SOCKET definition and I am > > unable to get this 'connected' ... > > Bob > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
