Hello Lizette, Thanks. Sorry for small mistake and now problem has resolved. Issue was with syntax issue with global csi we used.
Thanks for help again. On Sat, Jun 17, 2017 at 4:24 PM, Lizette Koehler <[email protected]> wrote: > The PTF is for DB2. > > PTF UI28808 is for A10. A10 is for DB2 V10. > > If you do not have the FMID for DB2 V10 in your GLOBAL zone, you could see > messages like: > > NO APPLICABLE ++VER > > > Verify the Global zone you are using for the RECEIVE contains the FMIDs > needed to do the RECEIVE > > I am not sure it is an RSU issue. Rather than receiving selective > maintenance, you should consider receiving all PTFs on all RSUxxxx. That > way you can selectively APPLY them but all needed fixes will be available. > When you select only certain fixes to RECEIVE, you may run into a condition > where you need other fixes you did not receive to apply it. By just doing > a blanket RECEIVE you do not need to worry so much about pre-reqs. > > Note: If you search IBM KC with APPLICABLE ++VER you would find this entry > > The "NO APPLICABLE ++VER" message does not usually indicate a problem. The > ESO tape may contain PTFs for multiple versions of the same product, but > the only PTFs received will be those for which there are FMIDs present in > your SMPE global zone. > > > > Lizette > > > > -----Original Message----- > > From: IBM Mainframe Discussion List [mailto:[email protected]] On > > Behalf Of venkat kulkarni > > Sent: Saturday, June 17, 2017 3:07 AM > > To: [email protected] > > Subject: SMPE not able to receive PTF > > > > Hello Group, > > > > I am trying to receive some PTF and getting below issue. > > > > 1PAGE 0001 - NOW SET TO GLOBAL ZONE DATE 06/17/17 TIME > 11:59:47 > > SMP/ > > > > > > > > > > RECEIVE > > 0022000 > > > > . > > 0023000 > > > > 1PAGE 0002 - NOW SET TO GLOBAL ZONE DATE 06/17/17 TIME > 12:00:02 > > SMP/ > > > > > > > > > > RECEIVE SUMMARY REPORT > > > > > > > > SYSMOD STATUS TYPE SOURCEID FEATURE STATUS FIELD > > COMMENTS > > UI28808 NOT RECEIVED PTF NO APPLICABLE > > ++VER > > > > NOT ASSIGNED PUT1507 SYSMOD NOT IN > RECEIVE > > STAT > > > > NOT ASSIGNED RSU1512 > > > > > > NOT ASSIGNED SMCCOR > > > > > > UI28997 NOT RECEIVED PTF NO APPLICABLE > > ++VER > > > > NOT ASSIGNED HIPER SYSMOD NOT IN > RECEIVE > > STAT > > > > NOT ASSIGNED PRP > > > > > > NOT ASSIGNED PUT1507 > > > > > > NOT ASSIGNED RSU1508 > > > > > > NOT ASSIGNED SMCCOR > > > > > > UI29001 NOT RECEIVED PTF NO APPLICABLE > > ++VER > > > > NOT ASSIGNED HIPER SYSMOD NOT IN > RECEIVE > > STAT > > > > NOT ASSIGNED PUT1507 > > > > > > NOT ASSIGNED RSU1508 > > > > > > NOT ASSIGNED SMCCOR > > > > > > UI29041 NOT RECEIVED PTF NO APPLICABLE > > ++VER > > > > NOT ASSIGNED PUT1507 SYSMOD NOT IN > RECEIVE > > STAT > > > > NOT ASSIGNED RSU1512 > > > > > > NOT ASSIGNED SMCCOR > > > > > > UI29092 NOT RECEIVED PTF NO APPLICABLE > > ++VER > > > > NOT ASSIGNED HIPER SYSMOD NOT IN > RECEIVE > > STAT > > > > NOT ASSIGNED PUT1507 > > > > > > NOT ASSIGNED RSU1508 > > > > > > > > > > I am unable to receive these PTF because my system is running with older > RSU > > and these ptf require minimum of RSU1508 or higher or any other reason > for > > not able to receive these PTF. > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
