Here are the commands I tried : HSEND FIXCDS B DB96.ARCHLOG2.B0000778 (message received) :
ARC0195I TYPE B, KEY DB96.ARCHLOG2.B0000778, FIXCDS DISPLAY, ERROR=RECORD NOT ARC0195I (CONT.) FOUND ARC1001I FIXCDS B DB96.ARCHLOG2.B0000778 COMMAND FAILED, RC=0015, REAS=0000 ARC1615I FIXCDS COMMAND REJECTED HSEND BDELETE 'DB2.ARCHLOG2.A0091613' ALL No error message received. I looked at the ERR 40 in the doc. It describes my problem however it is not clear what I should do. In this case the B record does not exist or missing. for example it says "If the backup version (C) record references a data set (B) record that does not exist, then a new (B) record is created and the version added". Not usre ...then a new(B) record is created and the version added. I do not understand this. Any suggestions? -------------------------------------------- On Wed, 7/26/17, retired mainframer <[email protected]> wrote: Subject: Re: DFHSM QUESTION To: [email protected] Received: Wednesday, July 26, 2017, 1:30 PM Please show the complete AUDIT and BDELETE commands you are using. Did you look up ERR40 in the "Error Codes and Diagnosis" section (section 3 in my copy) of the "Using the AUDIT Command" chapter (my chapter 67)? The table (51) identifies several possible causes and corrective actions. BDELETE is the proper action for only one of the causes. > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of willie bunter > Sent: Wednesday, July 26, 2017 7:27 AM > To: [email protected] > Subject: DFHSM QUESTION > > Good Day, > > I ran an AUDIT of the BCDS. I was 99% successfull of performing a clean up execept for > the following type dsns: > ERR 40 DB2.ARCHLOG2.A0091613 > HSMBACK.BACK.T592617.DB2.ARCHLOG2.I8257 MISSING > FIXCDS B DUMMY.RECOVER.MCB CREATE(X'00000014' X'0098257F') > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'0000002E' BITS(1.1.....)) > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'00000030' X'000100010001') > FIXCDS B DUMMY.RECOVER.MCB EXPAND(X'00000040') > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'00000050' + > > X'404040404040404040404040404040404040404040404040404040404040404040404040 > 404 > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'00000050' > HSMBACK.BACK.T592617.DB2.ARCHLOG > FIXCDS B DUMMY.RECOVER.MCB PATCH(X'00000082' BITS(01000010)) > BDELETE DUMMY.RECOVER.MCB > FIXCDS B DUMMY.RECOVER.MCB DELETE > END OF - ENHANCED AUDIT - LISTING - > > I tried a HSEND BDELETE 'DB2.ARCHLOG2.A0091613' ALL . The command which I > ran in batch was successful however when I ran another AUDIT the entry appears. I tried a > HSEND FIXCDS B DB2.ARCHLOG2.A0091613. Again the command was successful, > however the AUDIT says otherwise. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
