I think it's time to list the contents of the BCDS, I don't have HSM so I can't
provide the correct command,
HSEND LIST LEVEL(DB96) BCDS or (BACKUPCONTROLDATASET) OUTDATASET(xxx.yyy.xxx)
??
but I tent to agree with Lizette, the record in the BCDS does not exist
* RECORD NOT FOUND—The indicated record was not found; you could not delete
or update it.
Carmen ----- Original Message -----
From: "willie bunter" <[email protected]>
To: [email protected]
Sent: Thursday, July 27, 2017 8:52:37 AM
Subject: Re: DFHSM QUESTION
Here are the commands I tried :
HSEND FIXCDS B DB96.ARCHLOG2.B0000778 (message received) :
ARC0195I TYPE B, KEY DB96.ARCHLOG2.B0000778, FIXCDS DISPLAY, ERROR=RECORD NOT
ARC0195I (CONT.) FOUND
ARC1001I FIXCDS B DB96.ARCHLOG2.B0000778 COMMAND FAILED, RC=0015, REAS=0000
ARC1615I FIXCDS COMMAND REJECTED
HSEND BDELETE 'DB2.ARCHLOG2.A0091613' ALL
No error message received.
I looked at the ERR 40 in the doc. It describes my problem however it is not
clear what I should do. In this case the B record does not exist or missing.
for example it says "If the backup version (C) record references a data set (B)
record that does not exist, then a new (B) record is created and the version
added". Not usre ...then a new(B) record is created and the version added.
I do not understand this. Any suggestions?
--------------------------------------------
On Wed, 7/26/17, retired mainframer <[email protected]> wrote:
Subject: Re: DFHSM QUESTION
To: [email protected]
Received: Wednesday, July 26, 2017, 1:30 PM
Please show the complete AUDIT
and BDELETE commands you are using.
Did you look up ERR40 in the "Error Codes
and Diagnosis" section (section 3 in my copy) of the
"Using the AUDIT Command" chapter (my chapter
67)? The table (51) identifies several possible causes and
corrective actions. BDELETE is the proper action for only
one of the causes.
>
-----Original Message-----
> From: IBM
Mainframe Discussion List [mailto:[email protected]]
On
> Behalf Of willie bunter
> Sent: Wednesday, July 26, 2017 7:27 AM
> To: [email protected]
> Subject: DFHSM QUESTION
>
> Good Day,
>
> I ran an AUDIT of
the BCDS. I was 99% successfull of performing a clean up
execept for
> the following type dsns:
> ERR 40 DB2.ARCHLOG2.A0091613
> HSMBACK.BACK.T592617.DB2.ARCHLOG2.I8257
MISSING
> FIXCDS B DUMMY.RECOVER.MCB
CREATE(X'00000014' X'0098257F')
> FIXCDS B DUMMY.RECOVER.MCB
PATCH(X'0000002E' BITS(1.1.....))
> FIXCDS B DUMMY.RECOVER.MCB
PATCH(X'00000030' X'000100010001')
> FIXCDS B DUMMY.RECOVER.MCB
EXPAND(X'00000040')
> FIXCDS B
DUMMY.RECOVER.MCB PATCH(X'00000050' +
>
>
X'404040404040404040404040404040404040404040404040404040404040404040404040
> 404
> FIXCDS B
DUMMY.RECOVER.MCB PATCH(X'00000050'
> HSMBACK.BACK.T592617.DB2.ARCHLOG
> FIXCDS B DUMMY.RECOVER.MCB
PATCH(X'00000082' BITS(01000010))
> BDELETE DUMMY.RECOVER.MCB
> FIXCDS B DUMMY.RECOVER.MCB DELETE
> END OF - ENHANCED AUDIT - LISTING
-
>
> I tried a HSEND
BDELETE 'DB2.ARCHLOG2.A0091613' ALL . The command
which I
> ran in batch was successful
however when I ran another AUDIT the entry appears. I
tried a
> HSEND FIXCDS B
DB2.ARCHLOG2.A0091613. Again the command was
successful,
> however the AUDIT says
otherwise.
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive
access instructions,
send email to [email protected]
with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
