"I'd expect unexpected results"
Wait a second... I'm in a loop with that statement :)
My first thought was a disassembler if this is something pretty small,
and then try to pick out any assembled TPX macros and control block
references since I think those would be the most likely changes between
versions that would cause expected unexpected results. Still a lot of
guessing though.
On 5/9/2019 11:35 AM, Jousma, David wrote:
Probably not a good idea. Do you know if they were smpe installed? There
could be a copy in your SMPPTS, or SMPSTS datasets? Otherwise, try it, but
I'd expect unexpected results.
_____________________________________________________________________________________________________
Dave Jousma
AVP | Manager, Systems Engineering
Fifth Third Bank | 1830 East Paris Ave, SE | MD RSCB2H | Grand Rapids, MI
49546
616.653.8429 | fax: 616.653.2717
-----Original Message-----
From: IBM Mainframe Discussion List <IBM-MAIN@LISTSERV.UA.EDU> On Behalf Of
Peter
Sent: Thursday, May 9, 2019 2:24 PM
To: IBM-MAIN@LISTSERV.UA.EDU
Subject: Re: Assembly JCL for tpx 5.4
**CAUTION EXTERNAL EMAIL**
**DO NOT open attachments or click on links from unknown senders or unexpected
emails**
We have some user exits used for TPX 5.2 and unfortunately we don't know where
the source codes are located.
Is it ok to just copy over to 5.4 ?
On Fri, 3 May, 2019, 3:09 AM Mark Zelden, <m...@mzelden.com> wrote:
On Thu, 2 May 2019 15:44:14 -0500, Michael Cleary <
michaeljosephcle...@yahoo.com> wrote:
If the product is installed with SMPE best practice would be to
install
the exit via an SMPE USERMOD.
Not a bad idea, but I don't consider that necessary if the product
doesn't come with an LMOD for that exit in the product loadlib that is
being replaced by the one you want to create. There is no chance that
product maintenance will regress the exit which is the main reason you
would want a usermod. Good product installation documentation that
says there is an exit in use and putting it in a concatenated loadlib
or even directly into the product loadlib is fine as far as I'm
concerned. Just so the next pour sole that has to upgrade the product
next knows there is an exit and where the source code and asm/lnk JCL
is.
But that's just my opinion. Creating the usermod is more trouble than
I want to go through if I don't have to do it to protect the integrity
of the product installation.
Best Regards,
Mark
--
Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS ITIL
v3 Foundation Certified mailto:m...@mzelden.com Mark's MVS Utilities:
https://protect2.fireeye.com/url?k=146e0b62-4832ff6d-146e21fa-0cc47a33
347c-65139aa7751c56b9&u=http://www.mzelden.com/mvsutil.html
Systems Programming expert at
http://search390.techtarget.com/ateExperts/
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send
email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to
lists...@listserv.ua.edu with the message: INFO IBM-MAIN **CAUTION EXTERNAL
EMAIL**
**DO NOT open attachments or click on links from unknown senders or unexpected
emails**
This e-mail transmission contains information that is confidential and may be
privileged. It is intended only for the addressee(s) named above. If you
receive this e-mail in error, please do not read, copy or disseminate it in any
manner. If you are not the intended recipient, any disclosure, copying,
distribution or use of the contents of this information is prohibited. Please
reply to the message immediately by informing the sender that the message was
misdirected. After replying, please erase it from your computer system. Your
assistance in correcting this error is appreciated.
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
