James, what specifically did you mean by your first question: Did you TN3270 to the ICC adapter IP # before ipl'ing. How do you TN3270 to the IP # before ipl'ing and AFTER OSA is reset with the ipl? We had the TN3270 session ready before the IPL and then the OSA is reset in the IPL, so is there a timing issue with having to get the TN3270 session ready again for the IPL to find it to send the SAIPL screen? We think the IOCP and system config are correct. thanks again for your help Joan M. Gerads Systems & Programming SCICOM Data Services, Ltd. 10101 Bren Rd. East Minnetonka, MN 55343 Direct: 952-936-4170 Toll Free: 1-800-488-9087 Fax: 952-932-3936
This e-mail message, including any attachments, is intended only for the use of the recipient(s) and may contain privileged and confidential information, including but not limited to information that is protected under HIPAA or other state/federal privacy rules. Any unauthorized review; disclosure, copying, distribution or use is prohibited. If you have received this e-mail in error, please notify the sender immediately by reply e-mail and destroy all copies of the original message. ________________________________ From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of James M Sent: Monday, May 21, 2007 12:54 PM To: [email protected] Subject: Re: VM CONSOLE Experts...I need your help Joan- There's a lot to consider & check. Did you tn3270 to the ICC adapter IP # before ipl'ing? Is your iocp correct? Is your system config correct - console defined same as ipl device on ICC def. Are your ICC definitions correct - valid ipl device & pc ip # specified correctly I'm using the hummingbird emulator w/o problems. -James On 5/21/07, Joan Gerads <[EMAIL PROTECTED]> wrote: I have a couple more questions regarding setting up a VM console through OSA-ICC. z/VM version 5.2 - IBM z9 2096 BC processor 1 LPAR VM running multiple VSE guests 1) is there any software restrictions as far as 3270 emulator software running on the PC for the VM console to work on it? We are currently trying it with QWS Plus Version 4.0 (JollyGiant Software)? Is anyone else using that software? Or what is working for you? 2) secondly, on the HMC screen for OSA Advanced Facilities, 'active sessions configuration ', there is a field called 'MIFID'. In the IBM Redbook example, this field is set to a 'C ' on a VM console definition. On our screen, our VM console session, it is set to a '1' (the default?)....what exactly does ' C' mean? On a trial IPL of VM this last weekend, we could not get the OSA-ICC PC to come up as the VM console...I am pretty sure the system configuration is correct...we can 'DISC' from the dummy tube and 'RECONNECT' on the PC. We just have not figured out the VM IPL- how to get it to come up on the OSA-ICC PC. Thanks again for all your help! Joan M. Gerads Systems & Programming SCICOM Data Services, Ltd. 10101 Bren Rd. East Minnetonka, MN 55343 Direct: 952-936-4170 Toll Free: 1-800-488-9087 Fax: 952-932-3936 This e-mail message, including any attachments, is intended only for the use of the recipient(s) and may contain privileged and confidential information, including but not limited to information that is protected under HIPAA or other state/federal privacy rules. Any unauthorized review; disclosure, copying, distribution or use is prohibited. If you have received this e-mail in error, please notify the sender immediately by reply e-mail and destroy all copies of the original message. z/VM version 5.2 - IBM z9 2096 BC processor 1 LPAR VM running multiple VSE guests Two questions that I could use any advice, tips or tricks with: We recently migrated to z/VM 5.2 and an IBM z9 BC processor: 1) We recently switched our VM console from a dummy terminal to an OSA connection. We 'disc' VM on the dummy terminal and reconnected the console on the PC. That part worked fine. We will not be IPL'ing VM until this weekend so my question is: What do we need to do to have the OSA console be recognized as the VM console during an IPL of VM? For the dummy terminal, we had the address hard assigned in the system configuration under Console Definitions: Operator_Consoles....How do you do that same thing with an OSA VM console? An example would be helpful. Thanks 2) We are planning on moving our VM packs from one set of 3390 Disk drives to another set of 3390 Disk drives. Any hints on the steps that should be followed to make this an easy transition? Thanks in advance Joan M. Gerads Systems & Programming SCICOM Data Services, Ltd. 10101 Bren Rd. East Minnetonka, MN 55343 Direct: 952-936-4170 Toll Free: 1-800-488-9087 Fax: 952-932-3936 This e-mail message, including any attachments, is intended only for the use of the recipient(s) and may contain privileged and confidential information, including but not limited to information that is protected under HIPAA or other state/federal privacy rules. Any unauthorized review; disclosure, copying, distribution or use is prohibited. If you have received this e-mail in error, please notify the sender immediately by reply e-mail and destroy all copies of the original message.
