W 3 1
Means take the third word and move it to position 1 on the output record. ____________________________ Jim Hughes 603-271-5586 "Any fool can criticize when a man makes a mistake - and most of them do." ________________________________ From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Tuesday, June 03, 2008 11:12 AM To: [email protected] Subject: Re: Operator Terminal and the Programmable Operator Facility Thanks Bob, In the pipes command below, the 'SPECS w3 1' stage...can anyone tell me what the w3 1 means. I checke the manual and I think it means word...like the third word of the output for a length 1??? Can't figure this one out... Thanks. >>> Bob Bates <[EMAIL PROTECTED]> 6/2/2008 3:41 PM >>> Off the top of my head. In the OPERATOR's PROFILE EXEC 'PIPE CP Q OPERATOR | SPECS w3 1 | var termaddr 'CP DISC' 'CP SLEEP 1 SEC' 'XAUTOLOG OP1 ON' termaddr 'PROPST' or something along those lines. Bob Bates Enterprise Hosting Services - Enterprise Virtualization - z/VM and z/Linux <http://ehs.homestead.wellsfargo.com/Mainframe/zSS/zSE/zVM-zLinux/Pages/ default.aspx> w. (469)892-6660 c. (214) 907-5071 "This message may contain confidential and/or privileged information. If you are not the addressee or authorized to receive this for the addressee, you must not use, copy, disclose, or take any action based on this message or any information herein. If you have received this message in error, please advise the sender immediately by reply e-mail and delete this message. Thank you for your cooperation." ________________________________ From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Howard Rifkind Sent: Monday, June 02, 2008 2:34 PM To: [email protected] Subject: Operator Terminal and the Programmable Operator Facility Using the POF (programmable operatior facility) I would like to user the same terminal address as the one the Operator came up on when the system was IPL'ed. I know I can do a CP disconnect after the Operator does a PROPST and then log on the OP1 user to the same terminal address as the Operator was using and be able to received messages from the disconnected Operator running PROP and send command to the Operator via OP1. This currently works and isn't a problem as the Operator person is doing the CP Disc and then logging OP1. The issue for me is that the operations management does not want the operator person to have any interaction with the physical terminal during this procedure. So, I have to automate the process and I need some suggestions as how to do this. The Operator user id has to start PROP and some how run disconnected. I have to logon OP1 on the same termial to act as the Operator with human interaction. I looks easy enough at first but I can't figure out a reasonable way to do this. Running z/VM 5.3. Any suggestions will be appreciated. Thanks _____________ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash. _____________ LEGAL NOTICE Unless expressly stated otherwise, this message is confidential and may be privileged. It is intended for the addressee(s) only. Access to this E-mail by anyone else is unauthorized. If you are not an addressee, any disclosure or copying of the contents of this E-mail or any action taken (or not taken) in reliance on it is unauthorized and may be unlawful. If you are not an addressee, please inform the sender immediately, then delete this message and empty from your trash.
