I have the following in my SYSTEM CONFIG file: define vswitch vsw1 rdev 021C 0220
Do I need to attach 21C - 21E and 220 - 222 to any machine? Thanks, Billy On 16 Feb 2010 at 13:28, Scott Rohling wrote: > > oops -- that HOME statement should be: > > HOME > 10.68.0.6 255.255.255.0 VMVSWD > > You point to the 'LINK' (VMVSWD in this case).. I cut the line short in my > last post. > > Scott > > On Tue, Feb 16, 2010 at 1:25 PM, Scott Rohling <[email protected]> > wrote: > Ok - Before I show the TCPIP PROFILE -- here is a line from the TCPIP > directory entry: > > NICDEF A000 TYPE QDIO LAN SYSTEM VSW1 > > Our system has a VSWITCH called VSW1 .. TCPIP will use address A000 to > connect to it. > > In PROFILE TCPIP: > > DEVICE VMVSW OSD A000 PORTNAME VMVSW PORTNUMBER 0 AUTOR > LINK VMVSWD QDIOETHERNET VMVSW MTU 1492 > . > . > HOME > 10.68.0.6 255.255.255.0 VMVSW > > . > . > START VMVSW > > Really - just exactly like an OSA (it's a virtualized OSA) -- the only > difference is where your > device comes from --- a virtual NIC attached to a VSWITCH, instead of a > dedicated OSA. > You can make the switch by simply changing the directory entry for > TCPIP.. (just make sure > TCPIP has been granted access to the vswitch!) Use the same address as > you used for > your OSA and use it on the NICDEF statement. Bring TCPIP down and up > again - done. > > Scott > > > > > > On Tue, Feb 16, 2010 at 12:00 PM, Billy Bingham > <[email protected]> wrote: > Scott, > > Can you send me the TCPIP PROFILE that you have setup to use Vswitches? > > > Thanks, > > Billy > > > On 16 Feb 2010 at 11:40, Scott Rohling wrote: > > > > > Agreed -- I like connecting TCPIP to the VSWITCH and letting the > controllers manage the > > OSA's. It's also nice to be able to recycle TCPIP without affecting > Linux guests. > > > > Scott > > > > On Tue, Feb 16, 2010 at 11:27 AM, Mark Pace <[email protected]> wrote: > > Yes. > > > > It can be done either way. You can connect TCPIP to it's own OSA > connection, or > connect > > TCPIP to the vswitch. There may be good reasons for not having TCPIP > connected to > the > > vswitch, but I don't know what they would be. With vswitch having > automatic fail-over > when > > it has multiple OSA addresses, it's the way I run. > > > > > > > > On Tue, Feb 16, 2010 at 1:09 PM, Billy Bingham > <[email protected]> > wrote: > > Hello all, > > > > Risking the old saying that it's better to have someone think you're > stupid than to open > your > > mouth and remove all doubt... but :) > > > > I'm confused about Vswitches on z/VM... sorta. I know you define the > Vswitch in the > System > > Config file, but does the TCPIP guest running on z/VM also use that > Vswitch or does > TCP/IP > > use it's own OSA connection and other Liniux guests (In this case) use > the Vswitch? Is > there > > a 'cookbook' available for setting up Vswitches? > > > > Any hints and tips appreciated. > > > > > > Billy > > > > > > > > > > > > -- > > Mark Pace > > Mainline Information Systems > > 1700 Summit Lake Drive > > Tallahassee, FL. 32317 > > > > > > > > > > > > > >
