I use Deks Olje. It’s a 2 part system: #1 leaves an “oiled look” finish and if you follow with #2 you will get a “varnished” look finish. Very good stuff and very easy to work with and lasts longer than either oil or varnish.
Here’s a link: http://www.jamestowndistributors.com/userportal/show_product.do?pid=168 <http://www.jamestowndistributors.com/userportal/show_product.do?pid=168&familyName=Deks+Olje> &familyName=Deks+Olje As far as the “ridges and valley’s” if they aren’t too bad you can sand ‘em down then seal ‘em you your favorite stuff. If they are real bad, remember, you’re removing a lot of wood and the wood will be weak from the deterioration. I don’t know anyone that has tried to fill the “valleys”…may be time to replace ‘em…and now, time for a shameless plug…I have a pair of hand rails that I salvaged off a “Katrina boat” that are in pretty good shape. Mark, Gratis (6115) NOLA From: [email protected] [mailto:[email protected]] On Behalf Of Read Howarth Sent: Thursday, December 31, 2009 11:05 AM To: [email protected] Subject: Re: [IC27A] Bright Work Does anyone just oil their wood? If so, what do you use? For the wood that has been neglected in the past and developed ridges, do you fill the valleys? Read --- On Thu, 12/31/09, [email protected] <mailto:tedp249%40aol.com> <[email protected] <mailto:tedp249%40aol.com> > wrote: From: [email protected] <mailto:tedp249%40aol.com> <[email protected] <mailto:tedp249%40aol.com> > Subject: Re: [IC27A] Bright Work To: [email protected] <mailto:IC27A%40yahoogroups.com> Date: Thursday, December 31, 2009, 10:07 AM To all of my Catalina friends I have not met yet, A Happy and Healthy New Year to all. Derek, Thanks for the info, I would prefer to remove the bright work vs refinish in place. I did try to remove the companion way hatch slides last fall with out success. The screws came out easy but I could not remove either the outside or interior pieces. I am guessing that they were glued and screwed. Anyone have any feed back on this presumption? Also I see you have removed the trim work for the port and starboard sided (over the instruments in the attached photos) Mine appear to be screwed on from the outside but the screws appear to have been counter sunk and plugged. I can only assume that one needs to carefully dig or drill out the plugs to access the screws. Any thoughts on that one? -----Original Message----- From: Derek Atkin <atkin...@yahoo. com> To: ic...@yahoogroups. com Sent: Thu, Dec 31, 2009 9:39 am Subject: Re: [IC27A] Bright Work I find the results are much better and easier if you remove what you can off the boat: http://www.opus45. com/pics/ c27_brightwork2. jpg I got everything off by the companionway slides. Most of it just comes off with screws, and needs a little sealant to re-bed back into the boat. All of mine was neglected and needed to be sanded in order for it to look good.: Before: http://www.opus45. com/pics/ c27_brightwork_ before.jpg After: http://www.opus45. com/pics/ c27_brightwork_ after.jpg The stuff I used is called Penofin Marine Oil Finish: http://www.penofin. com/products_ marine.shtml I used Sikens on my Boston Whaler and it is just to thick, it really covers up the wood. This Penofin is much easier to work with, looks hand rubbbed when dry and protects the wood just as well. I bought a gallon for $46 at a local paint store and have used maybe 1/8 of it on the boat so far. Derek #4297 ____________ _________ _________ __ From: "captain...@aol. com" <captain...@aol. com> To: ic...@yahoogroups. com Sent: Thu, December 31, 2009 1:21:41 AM Subject: Re: [IC27A] Bright Work tape before you sand, if you believe in sanding. I prefer to use a Sikens or Armada non sand finish. No where as beautiful as varnish, but a lot less effort required to protect brightwork. David Hoyt Sovereignty Catalina 27 #65 In a message dated 12/25/2009 11:14:00 A.M. Eastern Standard Time, johnwjennings@ verizon.net writes: Well, you can tell the type of Christmas I am enjoying -- sitting around thinking about sailing. This spring will be time to take care of some neglected outside bright work. First I need to strip the old stuff off. I need suggestions and recommendation of the best way (inexpensive, little manual labor, and tidy) to do it. I think removing the wood work is not an option. What is the magic solution? John Jennings Barjoh 83 C27, #5267 Middle River, MD Dec 25, 2009 01:52:10 AM, _ic...@yahoogroups. IC2_ (mailto:IC27A@ yahoogroups. com) wrote: Jack, thanks much for the anch. tips. season greetings//leroy --- In _ic...@yahoogroups. IC2_ (mailto:IC27A@ yahoogroups. com) , "Jack Brennan" wrote: > > There's No Name Harbor at the southern end of Key Biscayne, near the > Cape Florida lighthouse. It's in the state park, so you can take walks. The > harbor is a good place to swim and/or do the boat bottom in warmer weather. > It costs about $10 to anchor. You can't tie up at the dock at night. > There's an anchorage near the entrance to Crandon Park marina that is > also a popular swimming place. Only good for east/southeast winds. Don't > bother with Crandon Park. There are better places to stay. > A little farther south, you can go to Boca Chita Key just to the north > of Elliott Key. It has a keyhole harbor. It's an uninhabited island that's > part of the national park. Very cool place to visit, as long as the > mosquitoes aren't out. The park service won't spray, saying skeeters are > part of the natural experience. Get into your cabin and put up the screens > before dusk. It's deserted during the week and crowded on the weekends, to > the point where you can't find space at the dock > Of course, there's Elliott Key. Elliott Key is also uninhabited. You > can anchor near the dock on the north end of the island. The dock itself is > just under four feet of depth at low tide. It's usually a party place on the > weekends. Same applies with mosquitoes. The marina at the south end of the > island has a channel with about 2 ½ feet of depth, unless the park service > has dredged it (unlikely). > You can also pick up a mooring at the new Dinner Key mooring field that > Miami just opened. There is dinghy access to the Grove, which is great for > those who like to party. > > > -----Original Message----- > From: _ic...@yahoogroups. IC2_ (mailto:IC27A@ yahoogroups. com) [mailto:_IC27A@ yahoogroups. IC2_ (mailto:IC27A@ yahoogroups. com) ]On Behalf Of Leroy > Sent: Thursday, December 24, 2009 5:37 PM > To: _ic...@yahoogroups. IC2_ (mailto:IC27A@ yahoogroups. com) > Subject: [IC27A] Re: Windsong II > > > nice vessel Paul. Do u sail in Biscayne bay? I have a 1983 tall rig ( see > pics of " MIRIAM TWO ", which i keep in Dania. Planning on a week of sailing > in the bay in early january. Have u ever anchored overnight in the bay ? and > where . tks// leroy > --- In _ic...@yahoogroups. IC2_ (mailto:IC27A@ yahoogroups. com) , "PAUL" > wrote: > > > > Well, Merry Christmas everyone. I'm pumped! I will pick up my new (well, > 1985 model) C27 and sail her home this week. Here's a link to my web album > of photos: _http://picasaweb. http://picahttp: //pihttp: //pic_ (http://picasaweb. google.com/ jumbonav/ WindsongII) > > > > > > > [Non-text portions of this message have been removed] > [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
