Thank you, Michael!!
On 9/3/15, 12:51 PM, "icinga-users on behalf of Michael Friedrich" <[email protected] on behalf of [email protected]> wrote: >Am 03.09.2015 um 20:45 schrieb Nobuo Matsushita: >> Thank you for your response, Michael. >> >> The web page doesn’t have the equation. It says what attribute I need to >> use. >> >> The other part of document shows; >> >> Flapping value = (# of actual state change/ ???) >> >> I can not read ??? Part. > >If you are referring to the migration docs from 1.x to 2.x, I wouldn't >go there unless you're having an existing 1.x system and require details >how it worked there. > >Probably your browser is just doing foobar :-) > >http://docs.icinga.org/icinga2/latest/doc/module/icinga2/chapter/migration >#differences-1x-2-flapping > >[--SNIP--] >The Icinga 1.x flapping detection uses the last 21 states of a service. >This value is hardcoded and cannot be changed. The algorithm on >determining a flapping state is as follows: > >flapping value = (number of actual state changes / number of possible >state changes) > >The flapping value is then compared to the low and high flapping >thresholds. > >The algorithm used in Icinga 2 does not store the past states but >calculcates the flapping threshold from a single value based on counters >and half-life values. Icinga 2 compares the value with a single flapping >threshold configuration attribute. >[--SNIP--] > >Kind regards, >Michael >> >> Nobuo >> >> >> On 9/3/15, 12:33 PM, "icinga-users on behalf of Michael Friedrich" >> <[email protected] on behalf of >> [email protected]> wrote: >> >>> Am 03.09.2015 um 20:13 schrieb Nobuo Matsushita: >>>> Hi all, >>>> >>>> I asked about flapping question before but I didn’t get any reply. So >>>> I am asking again. >>>> >>>> According to the Documentation, Icinga was not able to modify the >>>> flapping parameter. But for Icinga2, it looks like it can be >>>> configurable. >>>> >>>> But I am not sure how to change it. Can someone tell me how? The >>>> following is the image capture from the documentation: >>>> >>>> I can not see after “sta…..” >>>> >>>> Does anyone know what is written there? >>> Probably not the accurate place to look for. The flapping documentation >>> can be found here: >>> >>>http://docs.icinga.org/icinga2/latest/doc/module/icinga2/chapter/advance >>>d- >>> topics#check-flapping >>> >>> Kind regards, >>> Michael >>> >>>> Thanks >>>> >>>> Nobuo >>>> >>>> >>>> _______________________________________________ >>>> icinga-users mailing list >>>> [email protected] >>>> https://lists.icinga.org/mailman/listinfo/icinga-users >>> >>> -- >>> Michael Friedrich, DI (FH) >>> Senior Developer >>> >>> NETWAYS GmbH | Deutschherrnstr. 15-19 | D-90429 Nuernberg >>> Tel: +49 911 92885-0 | Fax: +49 911 92885-77 >>> GF: Julian Hein, Bernd Erk | AG Nuernberg HRB18461 >>> http://www.netways.de | [email protected] >>> >>> ** OSBConf 2015 - September - osbconf.org ** >>> ** OSMC 2015 - November - netways.de/osmc ** >>> _______________________________________________ >>> icinga-users mailing list >>> [email protected] >>> https://lists.icinga.org/mailman/listinfo/icinga-users >> _______________________________________________ >> icinga-users mailing list >> [email protected] >> https://lists.icinga.org/mailman/listinfo/icinga-users > > >-- >Michael Friedrich, DI (FH) >Senior Developer > >NETWAYS GmbH | Deutschherrnstr. 15-19 | D-90429 Nuernberg >Tel: +49 911 92885-0 | Fax: +49 911 92885-77 >GF: Julian Hein, Bernd Erk | AG Nuernberg HRB18461 >http://www.netways.de | [email protected] > >** OSBConf 2015 - September - osbconf.org ** >** OSMC 2015 - November - netways.de/osmc ** >_______________________________________________ >icinga-users mailing list >[email protected] >https://lists.icinga.org/mailman/listinfo/icinga-users _______________________________________________ icinga-users mailing list [email protected] https://lists.icinga.org/mailman/listinfo/icinga-users
