Hi all,
I've just installed Ubuntu 5.10 in my dual-boot box. I'm using
D-Link 502T for BSNL broadband & using the USB interface from windows
without any issues. Would like to use the same in Ubuntu. The D-Link
502T Modem/Router is not always on. The web interface leads me to
believe that its also is Linux-based.
Now these are the readings which I got from the lsusb
commands when the modem/router is plugged in :-
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 003: ID 2001:5b00 D-Link Corp. [hex]
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Does this mean that Linux has recognized the Modem/Router?
DMesg gives me this output :-
] Enabling APIC mode: Flat. Using 1 I/O APICs
[4294667.296000] Using ACPI (MADT) for SMP configuration information
[4294667.296000] Allocating PCI resources starting at 07800000 (gap:
07800000:f7 400000)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=/dev/hda12 ro quiet splash
[4294667.296000] mapped APIC to ffffd000 (fee00000)
[4294667.296000] mapped IOAPIC to ffffc000 (fec00000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 512 (order: 9, 8192 bytes)
[4294667.296000] Detected 1804.446 MHz processor.
[4294667.296000] Using pmtmr for high-res timesource
[4294667.296000] Console: colour VGA+ 80x25
[4294668.702000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[4294668.703000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[4294668.706000] Memory: 113668k/122816k available (1415k kernel code,
8564k res erved, 763k data, 224k init, 0k highmem)
[4294668.706000] Checking if this processor honours the WP bit even in
superviso r mode... Ok.
[4294668.706000] Calibrating delay loop... 3571.71 BogoMIPS (lpj=1785856)
[4294668.728000] Security Framework v1.0.0 initialized
[4294668.728000] SELinux: Disabled at boot.
[4294668.728000] Mount-cache hash table entries: 512
[4294668.728000] CPU: After generic identify, caps: 3febfbff 00000000
00000000 0 0000000 00000000 00000000 00000000
[4294668.728000] CPU: After vendor identify, caps: 3febfbff 00000000
00000000 00 000000 00000000 00000000 00000000
[4294668.728000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[4294668.728000] CPU: L2 cache: 256K
[4294668.728000] CPU: After all inits, caps: 3febfbff 00000000 00000000
00000080 00000000 00000000 00000000
[4294668.728000] CPU: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 03
[4294668.728000] Enabling fast FPU save and restore... done.
[4294668.728000] Enabling unmasked SIMD FPU exception support... done.
[4294668.728000] Checking 'hlt' instruction... OK.
[4294668.732000] Checking for popad bug... OK.
[4294668.732000] checking if image is initramfs... it is
[4294669.339000] Freeing initrd memory: 4828k freed
[4294669.343000] ACPI: Looking for DSDT in initrd... not found!
[4294669.404000] not found!
[4294669.414000] ENABLING IO-APIC IRQs
[4294669.414000] ..TIMER: vector=0x31 pin1=2 pin2=-1
[4294669.525000] NET: Registered protocol family 16
[4294669.525000] EISA bus registered
[4294669.525000] ACPI: bus type pci registered
[4294669.532000] PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=3
[4294669.532000] PCI: Using configuration type 1
[4294669.532000] mtrr: v2.0 (20020519)
[4294669.533000] ACPI: Subsystem revision 20050729
[4294669.543000] ACPI: Interpreter enabled
[4294669.543000] ACPI: Using IOAPIC for interrupt routing
[4294669.544000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294669.544000] PCI: Probing PCI hardware (bus 00)
[4294669.544000] ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
[4294669.547000] Boot video device is 0000:00:02.0
[4294669.547000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[4294669.547000] PCI: Transparent bridge - 0000:00:1e.0
[4294669.566000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294669.567000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT]
[4294669.570000] ACPI: Power Resource [URP1] (off)
[4294669.571000] ACPI: Power Resource [URP2] (off)
[4294669.571000] ACPI: Power Resource [FDDP] (off)
[4294669.571000] ACPI: Power Resource [LPTP] (off)
[4294669.572000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11
12 14 15 )
[4294669.572000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11
12 14 15 )
[4294669.572000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11
12 14 15 )
[4294669.573000] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11
12 14 15 )
[4294669.573000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11
12 14 15) *0, disabled.
[4294669.573000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11
12 14 15 )
[4294669.574000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11
12 14 15) *0, disabled.
[4294669.574000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11
12 14 15 )
[4294669.574000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294669.574000] pnp: PnP ACPI init
[4294669.578000] pnp: PnP ACPI: found 10 devices
[4294669.578000] PnPBIOS: Disabled by ACPI PNP
[4294669.578000] PCI: Using ACPI for IRQ routing
[4294669.578000] PCI: If a device doesn't work, try "pci=routeirq". If
it helps , post a report
[4294669.584000] audit: initializing netlink socket (disabled)
[4294669.584000] audit: initialized
[4294669.584000] VFS: Disk quotas dquot_6.5.1
[4294669.584000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294669.585000] devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
[4294669.585000] devfs: boot_options: 0x0
[4294669.585000] Initializing Cryptographic API
[4294669.585000] isapnp: Scanning for PnP cards...
[4294669.938000] isapnp: No Plug & Play device found
[4294669.968000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 i rq 1,12
[4294669.970000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294669.970000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294669.970000] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports,
IRQ shari ng enabled
[4294669.971000] ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[4294669.974000] ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[4294669.974000] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 21 (level,
low) -> I RQ 21
[4294669.974000] ttyS15 at I/O 0xcc08 (irq = 21) is a 16450
[4294669.975000] ttyS50 at I/O 0xcc10 (irq = 21) is a 8250
[4294669.975000] ttyS51 at I/O 0xcc18 (irq = 21) is a 16450
[4294669.975000] ttyS52 at I/O 0xcc20 (irq = 21) is a 8250
[4294669.975000] ttyS53 at I/O 0xcc28 (irq = 21) is a 8250
[4294669.978000] io scheduler noop registered
[4294669.978000] io scheduler anticipatory registered
[4294669.978000] io scheduler deadline registered
[4294669.978000] io scheduler cfq registered
[4294669.979000] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 bl ocksize
[4294669.980000] EISA: Probing bus 0 at eisa.0
[4294669.980000] EISA: Detected 0 cards.
[4294669.980000] NET: Registered protocol family 2
[4294669.990000] IP: routing cache hash table of 512 buckets, 4Kbytes
[4294669.990000] TCP established hash table entries: 4096 (order: 3,
32768 bytes )
[4294669.990000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[4294669.990000] TCP: Hash tables configured (established 4096 bind 4096)
[4294669.990000] NET: Registered protocol family 8
[4294669.990000] NET: Registered protocol family 20
[4294669.990000] ACPI wakeup devices:
[4294669.990000] USB1 USB2 USB3 EHCI ICHB PS2M PS2K UAR1 MC9
[4294669.990000] ACPI: (supports S0 S1 S4 S5)
[4294669.990000] Freeing unused kernel memory: 224k freed
[4294670.011000] input: AT Translated Set 2 keyboard on isa0060/serio0
[4294670.020000] vga16fb: initializing
[4294670.020000] vga16fb: mapped to 0xc00a0000
[4294670.155000] Console: switching to colour frame buffer device 80x30
[4294670.155000] fb0: VGA16 VGA frame buffer device
[4294671.282000] Capability LSM initialized
[4294671.299000] NET: Registered protocol family 1
[4294671.323000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294671.323000] ide: Assuming 33MHz system bus speed for PIO modes;
override wi th idebus=xx
[4294671.323000] ACPI: bus type ide registered
[4294671.329000] ICH4: IDE controller at PCI slot 0000:00:1f.1
[4294671.329000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> I RQ 18
[4294671.329000] ICH4: chipset revision 2
[4294671.329000] ICH4: not 100% native mode: will probe irqs later
[4294671.329000] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings:
hda:DMA, hdb: pio
[4294671.329000] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings:
hdc:DMA, hdd: pio
[4294671.329000] Probing IDE interface ide0...
[4294671.593000] hda: SAMSUNG SP0802N, ATA DISK drive
[4294672.205000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294672.205000] Probing IDE interface ide1...
[4294672.877000] hdc: SAMSUNG CD-R/RW SW-252B, ATAPI CD/DVD-ROM drive
[4294673.183000] ide1 at 0x170-0x177,0x376 on irq 15
[4294673.183000] ide2: I/O resource 0x3EE-0x3EE not free.
[4294673.183000] ide2: ports already in use, skipping probe
[4294673.183000] Probing IDE interface ide3...
[4294673.696000] Probing IDE interface ide4...
[4294674.208000] Probing IDE interface ide5...
[4294674.726000] hda: max request size: 1024KiB
[4294674.741000] hda: 156368016 sectors (80060 MB) w/2048KiB Cache,
CHS=16383/25 5/63, UDMA(33)
[4294674.741000] hda: cache flushes supported
[4294674.741000] /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8
p9 p10 p 11 p12 p13 p14 >
[4294674.859000] hdc: ATAPI 52X CD-ROM CD-R/RW drive, 8192kB Cache
[4294674.859000] Uniform CD-ROM driver Revision: 3.20
[4294675.458000] Attempting manual resume
[4294675.466000] swsusp: Suspend partition has wrong signature?
[4294675.500000] usbcore: registered new driver usbfs
[4294675.500000] usbcore: registered new driver hub
[4294675.502000] USB Universal Host Controller Interface driver v2.2
[4294675.502000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level,
low) -> I RQ 16
[4294675.502000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294675.502000] uhci_hcd 0000:00:1d.0: Intel Corporation
82801DB/DBL/DBM (ICH4/ ICH4-L/ICH4-M) USB UHCI Controller #1
[4294675.564000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus num ber 1
[4294675.564000] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e400
[4294675.564000] hub 1-0:1.0: USB hub found
[4294675.564000] hub 1-0:1.0: 2 ports detected
[4294675.567000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> I RQ 19
[4294675.567000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294675.567000] uhci_hcd 0000:00:1d.1: Intel Corporation
82801DB/DBL/DBM (ICH4/ ICH4-L/ICH4-M) USB UHCI Controller #2
[4294675.629000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus num ber 2
[4294675.629000] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800
[4294675.629000] hub 2-0:1.0: USB hub found
[4294675.629000] hub 2-0:1.0: 2 ports detected
[4294675.632000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> I RQ 18
[4294675.632000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294675.632000] uhci_hcd 0000:00:1d.2: Intel Corporation
82801DB/DBL/DBM (ICH4/ ICH4-L/ICH4-M) USB UHCI Controller #3
[4294675.694000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus num ber 3
[4294675.694000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00
[4294675.694000] hub 3-0:1.0: USB hub found
[4294675.694000] hub 3-0:1.0: 2 ports detected
[4294675.730000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level,
low) -> I RQ 23
[4294675.730000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294675.730000] ehci_hcd 0000:00:1d.7: Intel Corporation 82801DB/DBM
(ICH4/ICH4 -M) USB2 EHCI Controller
[4294675.730000] ehci_hcd 0000:00:1d.7: debug port 1
[4294675.730000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus num ber 4
[4294675.730000] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff7bc00
[4294675.734000] PCI: cache line size of 128 is not supported by device
0000:00: 1d.7
[4294675.734000] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00,
driver 1 0 Dec 2004
[4294675.734000] hub 4-0:1.0: USB hub found
[4294675.734000] hub 4-0:1.0: 6 ports detected
[4294678.547000] ACPI: CPU0 (power states: C1[C1])
[4294678.547000] ACPI: Processor [CPU1] (supports 8 throttling states)
[4294678.870000] Attempting manual resume
[4294678.880000] swsusp: Suspend partition has wrong signature?
[4294678.890000] ReiserFS: hda12: found reiserfs format "3.6" with
standard jour nal
[4294679.272000] ReiserFS: hda12: using ordered data mode
[4294679.284000] ReiserFS: hda12: journal params: device hda12, size
8192, journ al first block 18, max trans len 1024, max batch 900, max
commit age 30, max tra ns age 30
[4294679.286000] ReiserFS: hda12: checking transaction log (hda12)
[4294679.318000] ReiserFS: hda12: Using r5 hash to sort names
[4294680.292000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294684.414000] Adding 602396k swap on /dev/hda13. Priority:-1 extents:1
[4294692.343000] parport: PnPBIOS parport detected.
[4294692.343000] parport0: PC-style at 0x378, irq 7 [PCSPP]
[4294692.434000] lp0: using parport0 (interrupt-driven).
[4294692.463000] mice: PS/2 mouse device common for all mice
[4294692.874000] input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
[4294693.445000] ts: Compaq touchscreen protocol output
[4294694.851000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[EMAIL PROTECTED] edhat.com
[4294695.784000] cdrom: hdc: mrw address space DMA selected
[4294701.818000] ReiserFS: hda14: found reiserfs format "3.6" with
standard jour nal
[4294702.480000] ReiserFS: hda14: using ordered data mode
[4294702.481000] ReiserFS: hda14: journal params: device hda14, size
8192, journ al first block 18, max trans len 1024, max batch 900, max
commit age 30, max tra ns age 30
[4294702.483000] ReiserFS: hda14: checking transaction log (hda14)
[4294702.503000] ReiserFS: hda14: Using r5 hash to sort names
[4294703.914000] Linux agpgart interface v0.101 (c) Dave Jones
[4294703.929000] agpgart: Detected an Intel 845G Chipset.
[4294703.929000] agpgart: Detected 8060K stolen memory.
[4294703.959000] agpgart: AGP aperture is 128M @ 0xd0000000
[4294704.416000] hw_random: RNG not detected
[4294704.555000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294704.573000] shpchp: shpc_init : shpc_cap_offset == 0
[4294704.573000] shpchp: Standard Hot Plug PCI Controller Driver
version: 0.4
[4294705.227000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level,
low) -> I RQ 17
[4294705.227000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[4294705.536000] intel8x0_measure_ac97_clock: measured 49413 usecs
[4294705.536000] intel8x0: clocking to 48000
[4294707.390000] Real Time Clock Driver v1.12
[4294707.447000] input: PC Speaker
[4294707.756000] Floppy drive(s): fd0 is 1.44M
[4294707.771000] FDC 0 is a post-1991 82077
[4294710.932000] ACPI: Power Button (FF) [PWRF]
[4294710.932000] ACPI: Power Button (CM) [PWRB]
[4294711.023000] ibm_acpi: ec object not found
[4294718.162000] [drm] Initialized drm 1.0.0 20040925
[4294718.182000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level,
low) -> I RQ 16
[4294718.190000] [drm] Initialized i915 1.2.0 20040405 on minor 0: Intel
Corpora tion 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device
[4294718.191000] mtrr: base(0xd0020000) is not aligned on a
size(0x800000) bound ary
[4294722.059000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[4294722.059000] apm: overridden by ACPI.
[4294723.017000] Bluetooth: Core ver 2.7
[4294723.017000] NET: Registered protocol family 31
[4294723.017000] Bluetooth: HCI device and connection manager initialized
[4294723.017000] Bluetooth: HCI socket layer initialized
[4294723.052000] Bluetooth: L2CAP ver 2.7
[4294723.052000] Bluetooth: L2CAP socket layer initialized
[4294723.086000] Bluetooth: RFCOMM ver 1.5
[4294723.086000] Bluetooth: RFCOMM socket layer initialized
[4294723.086000] Bluetooth: RFCOMM TTY layer initialized
[4294738.124000] NET: Registered protocol family 10
[4294738.124000] Disabled Privacy Extensions on device c02eb280(lo)
[4294738.124000] IPv6 over IPv4 tunneling driver
[4294765.980000] cdrom: hdc: mrw address space DMA selected
[4294766.295000] cdrom: hdc: mrw address space DMA selected
[4294766.631000] ISO 9660 Extensions: Microsoft Joliet Level 3
[4294766.643000] ISOFS: changing to secondary root
[4295572.048000] usb 2-1: new full speed USB device using uhci_hcd and
address 2
lsmod gives me this output :-
isofs 32824 1
udf 75524 0
ipv6 217408 6
rfcomm 34972 0
l2cap 22404 5 rfcomm
bluetooth 43012 4 rfcomm,l2cap
speedstep_lib 4228 0
cpufreq_powersave 1920 0
cpufreq_stats 5124 0
cpufreq_userspace 4444 0
cpufreq_ondemand 5916 0
cpufreq_conservative 6820 0
freq_table 4484 1 cpufreq_stats
i915 17920 1
drm 58004 2 i915
tc1100_wmi 6916 0
video 16004 0
battery 9604 0
container 4608 0
i2c_acpi_ec 5760 0
i2c_core 19728 1 i2c_acpi_ec
button 6672 0
pcc_acpi 11392 0
sony_acpi 5516 0
ac 4996 0
dev_acpi 11396 0
hotkey 9508 0
floppy 52692 0
pcspkr 3652 0
rtc 11832 0
snd_intel8x0 30144 1
snd_ac97_codec 72188 1 snd_intel8x0
snd_pcm_oss 46368 0
snd_mixer_oss 16128 1 snd_pcm_oss
snd_pcm 78344 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 21764 1 snd_pcm
snd 48644 8
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 9184 1 snd
snd_page_alloc 10120 2 snd_intel8x0,snd_pcm
tpm_nsc 6528 0
tpm_atmel 5504 0
tpm 9504 2 tpm_nsc,tpm_atmel
shpchp 80612 0
pci_hotplug 24628 1 shpchp
intel_agp 21276 1
agpgart 32328 3 drm,intel_agp
nls_iso8859_1 4224 8
nls_cp437 5888 9
vfat 12288 8
fat 46492 1 vfat
dm_mod 50364 1
tsdev 7616 0
evdev 9088 0
psmouse 26116 0
mousedev 10912 1
parport_pc 31812 1
lp 11460 0
parport 32072 2 parport_pc,lp
md 40656 0
reiserfs 217200 2
thermal 13192 0
processor 23100 1 thermal
fan 4740 0
ehci_hcd 29448 0
uhci_hcd 28048 0
usbcore 104188 3 ehci_hcd,uhci_hcd
ide_cd 36996 1
cdrom 33952 1 ide_cd
ide_disk 16128 12
ide_generic 1664 0
piix 9476 1
ide_core 125268 4 ide_cd,ide_disk,ide_generic,piix
unix 24624 620
vesafb 8088 0
capability 5000 0
commoncap 6784 1 capability
vga16fb 12232 1
vgastate 8320 1 vga16fb
softcursor 2432 2 vesafb,vga16fb
cfbimgblt 2944 2 vesafb,vga16fb
cfbfillrect 3840 2 vesafb,vga16fb
cfbcopyarea 4480 2 vesafb,vga16fb
fbcon 34176 72
tileblit 2560 1 fbcon
font 8448 1 fbcon
bitblit 5248 1 fbcon
Now while installing Ubuntu the Modem/Router was not kept on, so do any
modules have to be installed, if yes how?
If anyone has tried & successfully done this, a walkthrough would be
great. Don't want to use Ethernet.
Thanx in anticipation.
--
Shirish Agarwal
Life is a dream Enjoy it!
Creative Commons, Attribution
Non-commercial, non-derivative
_______________________________________________
ilugd mailinglist -- [email protected]
http://frodo.hserus.net/mailman/listinfo/ilugd
Archives at: http://news.gmane.org/gmane.user-groups.linux.delhi
http://www.mail-archive.com/[email protected]/
