> -----Original Message-----
> From: Srikanth V, NagaVenkata <[email protected]>
> Sent: Monday, September 23, 2024 11:59 AM
> To: Kandpal, Suraj <[email protected]>; Murthy, Arun R
> <[email protected]>; [email protected]; intel-
> [email protected]
> Cc: Murthy, Arun R <[email protected]>
> Subject: RE: [PATCH 2/3] drm/i915/dp: read Aux RD interval after reading the
> FFE preset
>
> > > -----Original Message-----
> > > From: Intel-xe <[email protected]> On Behalf Of
> > > Arun R Murthy
> > > Sent: Thursday, September 12, 2024 10:36 AM
> > > To: [email protected]; [email protected]
> > > Cc: Murthy, Arun R <[email protected]>; Srikanth V,
> > > NagaVenkata <[email protected]>
> > > Subject: [PATCH 2/3] drm/i915/dp: read Aux RD interval after reading
> > > the FFE preset
> > >
> > > DP Source should be reading AUX_RD interval after we get adjusted
> > > TX_FFE_PRESET_VALUE from the DP Sink. (before actually adjusting in
> > > DP
> > > Source)
> >
> > I think mentioning the dp spec reference here would be helpful
> >
> Please refer to Figure 3-52: 128b132b DP DPTC LANEx_CHANNEL_EQ_DONE
> Sequence of DP2.1a spec.
I think you can update your commit message to say DP2.1a spec Fig. 3-52
Regards,
Suraj Kandpal
>
> > >
> > > Signed-off-by: Srikanth V NagaVenkata
> > > <[email protected]>
> > > Signed-off-by: Arun R Murthy <[email protected]>
> > > ---
> > > .../gpu/drm/i915/display/intel_dp_link_training.c | 12 ++++++------
> > > 1 file changed, 6 insertions(+), 6 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/i915/display/intel_dp_link_training.c
> > > b/drivers/gpu/drm/i915/display/intel_dp_link_training.c
> > > index f41b69840ad9..ca179bed46ad 100644
> > > --- a/drivers/gpu/drm/i915/display/intel_dp_link_training.c
> > > +++ b/drivers/gpu/drm/i915/display/intel_dp_link_training.c
> > > @@ -1419,12 +1419,6 @@ intel_dp_128b132b_lane_eq(struct intel_dp
> > > *intel_dp,
> > > for (try = 0; try < max_tries; try++) {
> > > fsleep(delay_us);
> > >
> > > - /*
> > > - * The delay may get updated. The transmitter shall read the
> > > - * delay before link status during link training.
> > > - */
> > > - delay_us =
> > > drm_dp_128b132b_read_aux_rd_interval(&intel_dp->aux);
> > > -
> > > if (drm_dp_dpcd_read_link_status(&intel_dp->aux,
> > > link_status) < 0) {
> > > lt_err(intel_dp, DP_PHY_DPRX, "Failed to read link
> > status\n");
> > > return false;
> > > @@ -1457,6 +1451,12 @@ intel_dp_128b132b_lane_eq(struct intel_dp
> > > *intel_dp,
> > > lt_err(intel_dp, DP_PHY_DPRX, "Failed to update TX
> > FFE
> > > settings\n");
> > > return false;
> > > }
> > > +
> > > + /*
> > > + * The delay may get updated. The transmitter shall read the
> > > + * delay before link status during link training.
> > > + */
> >
> > The comment needs to be updated as this is not being done before link
> > status Also a question does this not conflict with the requirement we
> > previously had (reading it before link status) ?
> >
> > Regards,
> > Suraj Kandpal
> >
> > Regards,
> > Suraj Kandpal
> >
> > > + delay_us =
> > > drm_dp_128b132b_read_aux_rd_interval(&intel_dp->aux);
> > > }
> > >
> > > if (try == max_tries) {
> > > --
> > > 2.25.1
