On Wed, Nov 20, 2024 at 11:08:35AM +0530, Nemesa Garg wrote:
> Replace adjusted_mode with pipe_mode in pch_panel_fitting
> so as to that final pipe src width and height is used after
> joiner calculation. De-couple the current intel_panel_fitting
> function, one pre-ilk and one post-ilk, as post-ilk
> pch_panel_fitting is called from pipe_config.
>
> Signed-off-by: Nemesa Garg <[email protected]>
> ---
> drivers/gpu/drm/i915/display/intel_display.c | 7 +++
> drivers/gpu/drm/i915/display/intel_pfit.c | 59 +++++++++++++-------
> 2 files changed, 47 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_display.c
> b/drivers/gpu/drm/i915/display/intel_display.c
> index 9db255bb1230..6ad47cf0d419 100644
> --- a/drivers/gpu/drm/i915/display/intel_display.c
> +++ b/drivers/gpu/drm/i915/display/intel_display.c
> @@ -4865,6 +4865,13 @@ copy_joiner_crtc_state_modeset(struct
> intel_atomic_state *state,
> drm_dp_tunnel_ref_get(primary_crtc_state->dp_tunnel_ref.tunnel,
> &secondary_crtc_state->dp_tunnel_ref);
>
> + if (secondary_crtc_state->pch_pfit.enabled) {
> + struct drm_rect *dst = &secondary_crtc_state->pch_pfit.dst;
> + int y = dst->y1;
> +
> + drm_rect_translate_to(dst, 0, y);
> + }
> +
> copy_joiner_crtc_state_nomodeset(state, secondary_crtc);
>
> secondary_crtc_state->uapi.mode_changed =
> primary_crtc_state->uapi.mode_changed;
> diff --git a/drivers/gpu/drm/i915/display/intel_pfit.c
> b/drivers/gpu/drm/i915/display/intel_pfit.c
> index fb6387b537b7..b2619e1c4021 100644
> --- a/drivers/gpu/drm/i915/display/intel_pfit.c
> +++ b/drivers/gpu/drm/i915/display/intel_pfit.c
> @@ -181,18 +181,19 @@ static int pch_panel_fitting(struct intel_crtc_state
> *crtc_state,
> const struct drm_connector_state *conn_state)
> {
> struct intel_display *display = to_intel_display(crtc_state);
> - const struct drm_display_mode *adjusted_mode =
> - &crtc_state->hw.adjusted_mode;
> + const struct drm_display_mode *pipe_mode =
> + &crtc_state->hw.pipe_mode;
> int pipe_src_w = drm_rect_width(&crtc_state->pipe_src);
> int pipe_src_h = drm_rect_height(&crtc_state->pipe_src);
> - int ret, x, y, width, height;
> + int num_pipes = intel_crtc_num_joined_pipes(crtc_state);
> + int ret, x, y, width, height, hdisplay_full, src_w_full;
>
> if (crtc_state->joiner_pipes)
> return 0;
>
> /* Native modes don't need fitting */
> - if (adjusted_mode->crtc_hdisplay == pipe_src_w &&
> - adjusted_mode->crtc_vdisplay == pipe_src_h &&
> + if (pipe_mode->crtc_hdisplay == pipe_src_w &&
> + pipe_mode->crtc_vdisplay == pipe_src_h &&
> crtc_state->output_format != INTEL_OUTPUT_FORMAT_YCBCR420)
> return 0;
>
> @@ -200,46 +201,66 @@ static int pch_panel_fitting(struct intel_crtc_state
> *crtc_state,
> case DRM_MODE_SCALE_CENTER:
> width = pipe_src_w;
> height = pipe_src_h;
> - x = (adjusted_mode->crtc_hdisplay - width + 1)/2;
> - y = (adjusted_mode->crtc_vdisplay - height + 1)/2;
> + x = (pipe_mode->crtc_hdisplay - width + 1) / 2;
> + y = (pipe_mode->crtc_vdisplay - height + 1) / 2;
> + /*
> + * The x-coordinate for Primary should be calculated in such a
> way
> + * that it remains consistent whether the pipes are joined or
> not.
> + * This means we need to consider the full width of the display
> even
> + * when the pipes are joined. The x-coordinate for secondaries
> is 0
> + * because it starts at the leftmost point of its own display
> area,
> + * ensuring that the framebuffer is centered within Pipe B’s
> portion
> + * of the overall display.
> + */
> + if (intel_crtc_is_joiner_primary(crtc_state)) {
> + hdisplay_full = pipe_mode->crtc_hdisplay * num_pipes;
> + src_w_full = width * num_pipes;
> + x = (hdisplay_full - src_w_full + 1) / 2;
> + }
Ugh. This stuff is getting quite nasty. I'm thinking it'll be a lot
cleaner if we in fact don't move the pch_panel_fitting() call from
its current location, and instead do something like this later:
joiner_adjust_pfit_dst()
{
area = pipe_area();
if (!pit.enable)
return;
rect_intersect(pfit.dst, area);
rect_translate(pfit.dst, -area.x1, -area.y1);
}
where pipe_area() (or whatever we want to call it) gives you
per-pipe output area, relative to the origing of the full
joined output. It should look quite similar to a combination
of intel_joiner_adjust_pipe_src()+intel_joiner_adjust_pipe_src()
except using crtc_hdisplay/vdisplay instead of pipe_src.
I'm also wondering what would happed if we use mode=CENTER but
the pfit dst window doesn't extend into all of the joined
pipes? Dunno if there's any way to have a zero sized pipe_src
for some of the pipes or not. If not I suppose we'll just have
to return an error...
--
Ville Syrjälä
Intel
