Here is a fixed version (from the UPS Bundle.zip file on the website)
<!--
APC UPS (com.dartware.ups.apc)
Custom Probe for InterMapper (http://www.intermapper.com)
Please feel free to use this as a base for further development.
Part of the UPS Probe Bundle -- Current Version: 2.4 / 31 August 2005.
Bugs or Requests? Please contact us: [EMAIL PROTECTED]
Revisions: (Probe Version reflects version of UPS Probe Bundle)
Created -- 19 July 2005 by jkj.
Updated for "display_name" change (IM 4.4) - 31 August 2005 by jkj.
Updated for Input Volts to use the rigth variable - 6 March 2006 by Jakob
Peterhänsel.
-->
<header>
"type" = "custom-snmp"
"package" = "com.dartware"
"probe_name" = "ups.apc"
"human_name" = "APC UPS"
"version" = "3.0"
"address_type" = "IP, AT"
"port_number" = "161"
"display_name" = "Network Devices/UPS/APC UPS"
</header>
<description>
\g0i++\For APC UPS devices.\p--\
\b++\A. Probed MIB(s)\p--\
\i\This probe works best with devices which have implemented the listed
MIB(s).\p\
(1 of 1) \b\APC UPS MIB\p\ [... enterprises.apc.products.hardware.ups / ...
1.3.6.1.4.1.318.1.1.1]
\b++\B. Displayed Values\p--\
UPS: model, firmware, status, (\i\battery\p\: capacity, time remaining,
temperature, replacement status), (\i\output\p\: load percent, volts, amps,
frequency), (\i\input\p\: volts, voltage range over last minute, frequency,
last input failure).
\b++\C. Alarms\p--\
(1 of 3) If unit goes onto battery or goes off-line.
(2 of 3) If battery needs replacement.
(3 of 3) If the battery temperature exceeds user-specified thresholds (see
"Paramaters" below).
\b++\D. Warnings\p--\
(1 of 2) If unit goes onto "Smart Trim" or "Smart Boost"
(2 of 2) If the battery temperature exceeds user-specified thresholds (see
"Paramaters" below).
\b++\E. Parameters\p--\
(1 of 5) \i\Units of Temperature (C / F)\p\: Determines how the following
thresholds are interpreted.
(2 of 5) \i\Alarm Threshold - Low Temp\p\: Threshold for alarm state (see
above).
(3 of 5) \i\Warning Threshold - Low Temp\p\: Threshold for alarm state (see
above).
(4 of 5) \i\Warning Threshold - High Temp\p\: Threshold for warning state (see
above).
(5 of 5) \i\Alarm Threshold - High Temp\p\: Threshold for warning state (see
above).
\bG3\Bugs or Requests? \p\\iU=mailto:[EMAIL PROTECTED] contact us.\p\
</description>
<parameters>
"Units of Temperature (C / F)" = "C"
"Alarm Threshold - Low Temp" = "0"
"Warning Threshold - Low Temp" = "10"
"Warning Threshold - High Temp" = "38"
"Alarm Threshold - High Temp" = "40"
</parameters>
<snmp-device-properties>
"apcups" = "false"
</snmp-device-properties>
<snmp-device-variables>
model, 1.3.6.1.4.1.318.1.1.1.1.1.1.0, DEFAULT, "" <!--
upsBasicIdentModel -->
firmware, 1.3.6.1.4.1.318.1.1.1.1.2.1.0, DEFAULT, "" <!--
upsAdvIdentFirmwareRevision -->
<!-- battery status -->
secs, 1.3.6.1.4.1.318.1.1.1.2.1.2.0, DEFAULT, "" <!--
upsBasicBatteryTimeOnBattery -->
batTimeOn, ($outCode = 3)?", UPS has been on battery for $secs
seconds.":"", CALCULATION
batTempC, 1.3.6.1.4.1.318.1.1.1.2.2.2.0, DEFAULT, "Battery
Temperature (¡C)" <!-- upsAdvBatteryTemperature -->
batTempF, $batTempC*9/5+32, CALCULATION, "Battery Temperature (¡F)"
leftCharge, 1.3.6.1.4.1.318.1.1.1.2.2.1.0, DEFAULT, "Battery Capacity
(%)" <!-- upsAdvBatteryCapacity -->
batMin, 1.3.6.1.4.1.318.1.1.1.2.2.3.0, DEFAULT, "Battery Minutes
Left" <!-- upsAdvBatteryRunTimeRemaining -->
timeLeft, substr("$batMin",0,-11), CALCULATION
replaceDate, 1.3.6.1.4.1.318.1.1.1.2.1.3.0, DEFAULT, "" <!--
upsBasicBatteryLastReplaceDate -->
replaceCode, 1.3.6.1.4.1.318.1.1.1.2.2.4.0, DEFAULT,
"{noBatteryNeedsReplacing(1),batteryNeedsReplacing(2)}" <!--
upsAdvBatteryReplaceIndicator -->
replaceStatus, ($replaceCode=1)?"still functioning":"\\1b\\needs to be
replaced\\3p\\", CALCULATION
<!-- input status -->
inVolt, 1.3.6.1.4.1.318.1.1.1.3.2.1.0, DEFAULT, "Input Voltage (Volts)"
<!-- upsAdvInputLineVoltage -->
inVMax, 1.3.6.1.4.1.318.1.1.1.3.2.2.0, DEFAULT, "" <!--
upsAdvInputMaxLineVoltage -->
inVMin, 1.3.6.1.4.1.318.1.1.1.3.2.3.0, DEFAULT, "" <!--
upsAdvInputMinLineVoltage -->
inRange, "$inVMin-${inVMax}V", CALCULATION, ""
inFreq, 1.3.6.1.4.1.318.1.1.1.3.2.4.0, DEFAULT, "Input Frequency (Hz)"
<!-- upsAdvInputFrequency -->
<!-- output status -->
ouLoad, 1.3.6.1.4.1.318.1.1.1.4.2.3.0, DEFAULT, "Output Load (%)" <!--
upsAdvOutputLoad -->
ouFreq, 1.3.6.1.4.1.318.1.1.1.4.2.2.0, DEFAULT, "Output Frequency (Hz)" <!--
upsAdvOutputFrequency -->
ouVolt, 1.3.6.1.4.1.318.1.1.1.4.2.1.0, DEFAULT, "Output Voltage (Volts)" <!--
upsAdvOutputVoltage -->
ouAmps, 1.3.6.1.4.1.318.1.1.1.4.2.4.0, DEFAULT, "OutPut Current (Amps)" <!--
upsAdvOutputCurrent -->
<!-- Code-to-Text Conversions -->
batCode, 1.3.6.1.4.1.318.1.1.1.2.1.1.0, DEFAULT, "upsBasicBatteryStatus"
<!-- unknown(1),batteryNormal(2),batteryLow(3) -->
batStatus,
($batCode=1)?"Unknown":($batCode=2)?"Normal":($batCode=3)?"Low":"Unknown
Battery Status Code", CALCULATION
outCode, 1.3.6.1.4.1.318.1.1.1.4.1.1.0, DEFAULT, "upsBasicOutputStatus"
<!--
{unknown(1),onLine(2),onBattery(3),onSmartBoost(4),timedSleeping(5),softwareBypass(6),off(7),rebooting(8),switchedBypass(9),hardwareFailureBypass(10),sleepingUntilPowerReturn(11),onSmartTrim(12)}
-->
out1, ($outCode=1)?"Unknown":($outCode=2)?"On Line (Not On
Battery)":($outCode=3)?"On Battery":($outCode=4)?"On Smart
Boost":($outCode=5)?"Timed Sleeping":($outCode=6)?"Software Bypass":"(!)Unknown
Output Status Code", CALCULATION
out2, ($outCode=7)?"Off":($outCode=8)?"Rebooting":($outCode=9)?"Switched
Bypass":($outCode=10)?"Hardware Failure Bypass":($outCode=11)?"Sleeping Until
Power Return":($outCode=11)?"On Smart Trim":"(!)Unknown Output Status Code",
CALCULATION
outputStatus, ($outCode<7)?"$out1":"$out2", CALCULATION
failCode, 1.3.6.1.4.1.318.1.1.1.3.2.5.0, DEFAULT,
"inputLineFailCause" <!-- code describing last input failure -->
<!--
{noTransfer(1),highLineVoltage(2),brownout(3),blackout(4),smallMomentarySag(5),deepMomentarySag(6),smallMomentarySpike(7),largeMomentarySpike(8),selfTest(9),rateOfVoltageChnage(10)}
-->
fail1, ($failCode=1)?"No Transfer":($failCode=2)?"High Line
Voltage":($failCode=3)?"Brown Out":($failCode=4)?"Black
Out":($failCode=5)?"Small Brief Sag":($failCode=6)?"Deep Brief Sag":"(!)Unknown
Input Failure Code", CALCULATION
fail2, ($failCode=7)?"Small Brief Spike":($failCode=8)?"Large Brief
Spike":($failCode=9)?"Self Test":($failCode=10)?"Rate of Voltage
Change":"(!)Unknown Input Failure Code", CALCULATION
failCause, ($failCode<7)?"$fail1":"$fail2", CALCULATION
<!-- Temperature variables -->
units, "${Units of Temperature (C / F)}", CALCULATION
tempAlarmLow, ${Alarm Threshold - Low Temp}, CALCULATION
tempWarningLow, ${Warning Threshold - Low Temp}, CALCULATION
tempWarningHigh, ${Warning Threshold - High Temp}, CALCULATION
tempAlarmHigh, ${Alarm Threshold - High Temp}, CALCULATION
tempRange, "$tempWarningLow-$tempWarningHigh $batUnits", CALCULATION
unitsC, "¡C", CALCULATION
unitsF, "¡F", CALCULATION
batUnits, ("$units" == "C")?"$unitsC":"$unitsF", CALCULATION
batTemp, ("$batUnits" == "$unitsC")?$batTempC:$batTempF, CALCULATION,
"Battery Temperature ($batUnits)"
</snmp-device-variables>
<snmp-device-thresholds>
warning: ($outCode = 4)||($outCode = 12) "Abnormal Input, Status =
$outputStatus"
warning: $batTemp < $tempWarningLow || $batTemp > $tempWarningHigh "UPS
battery temperature Warning: $batTemp $batUnits (Optimal Range: $tempRange)"
alarm: $batTimeOn > 0 "UPS has been running on battery for
$batTimeOn seconds."
alarm: $replaceCode = 2 "Battery needs to be replaced."
alarm: ($outCode <> 2)&&($outCode <> 4)&&($outCode <> 12) "$outputStatus"
alarm: $batTemp < $tempAlarmLow || $batTemp > $tempAlarmHigh "UPS battery
temperature Alarm: $batTemp $batUnits (Optimal Range: $tempRange)"
alarm: $batUnits <> $unitsC && $batUnits <> $unitsF "Bad Parameter: Units of
Temperature Must be either C or F"
</snmp-device-thresholds>
<snmp-device-display>
\p\\bM5\APC UPS (Single Phase) Information\p\\pM0\
\p\\pM4\ Model: \p\\pG0\$model\p\\pM0\
\p\\pM4\Firmware: \p\\pG0\$firmware\p\\pM0\
\p\\pM4\ Status: \p\\bG0\$outputStatus\p\\pM0\
\p\\pM4\ Battery: \p\\bG4\${chartable: #.: $leftCharge}\p\\bG4\ %\p\\iG3\
Charge, \p\\bG3\$timeLeft\p\\iG3\ left.\p\\pM0\
\p\\pM4\ \p\\iG3\Internal temperature is \p\\pG4\$batTempC\p\\iG3\
$unitsC / \p\\pG4\$batTempF\p\\iG3\ $unitsF.\p\\pM0\
\p\\pM4\ \p\\iG3\Last replaced on \p\\bG3\$replaceDate\p\\iG3\ and
$replaceStatus.\p\\pM0\
\p\\pM4\ Output: \p\\bG4\$ouLoad\p\\bG4\ %\p\\iG3\ Load; \p\\pG4\${chartable:
#.: $ouVolt}\p\\iG3\ Volts; \p\\pG4\${chartable: #.: $ouFreq}\p\\iG3\ Hz;
\p\\pG4\${chartable: #.#: $ouAmps}\p\\iG3\ Amps.\p\\pM0\
\p\\pM4\ Input: \p\\pG4\${chartable: #.: $inVolt}\p\\iG3\ Volts
(\p\\bG3\$inRange\p\\iG3\ over last minute); \p\\pG4\${chartable: #.:
$ouFreq}\p\\iG3\ Hz.\p\\pM0\
\p\\pM4\ \p\\iG3\Last input failure was a
\p\\bG3\$failCause\p\\pG0\.\p\\pM0\
\p\\bG3\Bugs or Requests? \p\\iG3\\U=mailto:[EMAIL PROTECTED] contact
us.\p\\pM0\
</snmp-device-display>
Jakob Peterhänsel
"Tell me why, don't we try, not to break our hearts
and make it so hard for our selfs"
P.S.B. 1987
Email: [EMAIL PROTECTED]
AIM: Marook
Phone: +45 22684961
On 06/04/2006, at 12:02, Jakob Peterhänsel wrote:
Hi,
It looks to me like the Input voltage is actually displaying the
Output voltage!
1: The numbers are Always the same
2: Even when the UPS is on Smart Boost
3: When I drag the Input number to a Chart, is labels it 'Output
Voltage (Volts)'.
Device Status
<snip>
Status: UP
Probe: APC UPS (port 161 SNMPv2c)
Up Time: 2 days, 0 hours, 28 minutes
SysName: CPHADM01
Availability: 100 % (of 1 hour, 51 minutes, 31 seconds)
Packet Loss: 0.0 % (of 468 total attempts) [Reset]
Recent Loss: None
Round-trip time: 46 msec
APC UPS (Single Phase) Information
Model: SMART-UPS 3000 RM
Firmware: 92.14.I
Status: On Smart Boost
Battery: 100 % Charge, 38 minutes left.
Internal temperature is 38 °C / 100 °F.
Last replaced on 4/15/02 and still functioning.
Output: 29 % Load; 237 Volts; 50 Hz; 0.0 Amps.
Input: 237 Volts (208-211V over last minute); 50 Hz.
Last input failure was a Black Out.
Bugs or Requests? Please contact us.
Recent Outages:
04/06 09:38:10: DOWN for 8 minutes, 21 seconds
04/05 15:41:54: DOWN for 24 seconds
Last updated Apr 06, 11:49:41; interval: 30 seconds
Reason: Abnormal Input, Status = On Smart Boost
Jakob Peterhänsel
"Tell me why, don't we try, not to break our hearts
and make it so hard for our selfs"
P.S.B. 1987
Email: [EMAIL PROTECTED]
AIM: Marook
Phone: +45 22684961
____________________________________________________________________
List archives:
http://www.mail-archive.com/intermapper-talk%40list.dartware.com/
To unsubscribe: send email to: [EMAIL PROTECTED]
