Hi, Andrew
Yes. I establish IPMI SOL. Thank you very much. I SOL connect Harwich by
CLI-2.3 tool.
I have other questions: IPMI vs AMT.
AMT is enterprise PC IT solution, IPMI is a server management solution. AMT
have many useful features and it also provider SDK and application tools to
complish the features. such as IDE-R.
Does IPMI provode those features?
How is the IPMI develop status? When do the IPMI 3.0 publish?
Will IPMI be replaced by AMT? What's the differences between AMT and IPMI?
Thanks & Regards,
Song Youquan
OTC-Beijing
Intel SSG/SSD
MOB: 13681289076
TEL: 010-82611515-1326
INET: 8-758-1326
LOC: Raycom 6W062
________________________________
From: Cress, Andrew R
Sent: 2007年9月10日 21:34
To: Song, Youquan
Subject: RE: [Ipmitool-devel] IPMI SOL failed on Intel Harwich
Oops, I forgot to add "-q 3" to the lan options.
________________________________
From: Cress, Andrew R
Sent: Monday, September 10, 2007 8:43 AM
To: Song, Youquan
Subject: RE: [Ipmitool-devel] IPMI SOL failed on Intel Harwich
Song Youquan,
There are a few things that need to be fixed in the configuration, shown in red
below.
First, the SOL Payload Access is disabled, which is probably the main reason
that it will not connect.
The SOL volatile Baud is not set, but if the payload were enabled, this might
be ok, since the non-volatile baud is set ok.
The LAN param (2) value means that only MD5 is set up for LAN sessions, which
may be ok, but is unusual.
Also, only the default user is configured for both LAN and serial, so users
like 'admin' would not be able to connect via SOL.
Here are two steps to correct these:
"ipmiutil lan -e -I 172.16.181.155 -u admin -p adminpswd -q 3 "
(should detect the gateway IP if the OS has it also, if not, add -G
172.16.181.9)
"ipmiutil serial -c -u admin -p adminpswd -q 3"
(defaults to 19.2kbps)
Then user 'admin' should be able to connect to 171.16.181.155 via SOL.
Andy
________________________________
From: Song, Youquan
Sent: Monday, September 10, 2007 5:10 AM
To: Cress, Andrew R
Cc: Song, Youquan
Subject: RE: [Ipmitool-devel] IPMI SOL failed on Intel Harwich
Hi Andrew,
Here is the information for "ipmiutil lan" and "ipmiutil serial", what's the
wrong with the setting paramenters?
[EMAIL PROTECTED] ~]# ipmiutil lan
ipmiutil ver 1.8
pefconfig ver 1.64
-- BMC version 0.56, IPMI version 2.0
pefconfig: GetPefEntry ...
PEFilter(01): 01 Temperature Sensor event - disabled for no action
PEFilter(02): 02 Voltage Sensor event - disabled for no action
PEFilter(03): 04 Fan Failure event - disabled for no action
PEFilter(04): 05 Chassis Intrusion event - disabled for no action
PEFilter(05): 08 Power Supply Fault event - disabled for no action
PEFilter(06): 0c Memory ECC Error event - disabled for no action
PEFilter(07): 0f FRB Failure event - disabled for no action
PEFilter(08): 07 BIOS POST Error event - disabled for no action
PEFilter(09): 13 Fatal NMI event - disabled for no action
PEFilter(10): 23 Watchdog Timer Reset event - disabled for no action
PEFilter(11): 12 System Restart event - disabled for no action
PEFilter(12): empty
PEF Control: 00
PEF Actions: 6f Alert PwrDn Reset PwrCyc DiagInt
PEF Startup Delay: 60 sec
PEF Alert Startup Delay: 60 sec
PEF Alert Policy[1]: 01 00 00 00 Disabled
PEF Alert Policy[2]: 02 00 00 00 Disabled
PEF Alert Policy[3]: 03 00 00 00 Disabled
PEF Alert Policy[4]: 04 00 00 00 Disabled
pefconfig: GetLanEntry for channel 1 ...
Lan Param(0) Set in progress: 00
Lan Param(1) Auth type support: 15 None MD5 Pswd
Lan Param(2) Auth type enables: 04 04 04 14 00
Lan Param(3) IP address: 172 16 181 155
Lan Param(4) IP addr src: 01 Static
Lan Param(5) MAC addr: 00 0e 0c 43 46 69
Lan Param(6) Subnet mask: 255 255 0 0
Lan Param(7) IPv4 header: 40 40 10
Lan Param(10) BMC grat ARP : 01
Lan Param(11) grat ARP interval: 09
Lan Param(12) Def gateway IP: 172 16 181 9
Lan Param(13) Def gateway MAC: 00 0f 35 fc d9 8a
Lan Param(14) Sec gateway IP: 0 0 0 0
Lan Param(15) Sec gateway MAC: 00 00 00 00 00 00
Lan Param(16) Community string: public
Lan Param(17) Num dest: 04
Lan Param(18) Dest type: 01 00 00 00 00
Lan Param(18) Dest type: 02 00 00 00 00
Lan Param(18) Dest type: 03 00 00 00 00
Lan Param(18) Dest type: 04 00 00 00 00
Lan Param(19) Dest address: 01 00 00 [0 0 0 0] 00 00 00 00 00 00
Lan Param(19) Dest address: 02 00 00 [0 0 0 0] 00 00 00 00 00 00
Lan Param(19) Dest address: 03 00 00 [0 0 0 0] 00 00 00 00 00 00
Lan Param(19) Dest address: 04 00 00 [0 0 0 0] 00 00 00 00 00 00
Lan Param(192) DHCP Server IP: 0 0 0 0
Lan Param(193) DHCP MAC Address: 00 00 00 00 00 00
Lan Param(194) DHCP Enable: 00
GetChanAcc(lan), ret = 0, new value = 02
Access = Always Avail, PEF Alerts Enabled
Channel Access Mode(Lan): 02 04
GetSOL for channel 1 ...
SOL Enable: 01 enabled
SOL Auth: c4 Admin
SOL Accum Interval: 04 32 20 msec
SOL Retry Interval: 06 02 20 msec
SOL nvol Baud Rate: 07 19.2k
SOL vol Baud Rate: 00 nobaud
SOL Payload Access(1,1): 00 00 00 00 disabled
SOL Payload Support(1): 03 00 15 00 00 00 00 00
Get User Access(1): 04 02 01 14 IPMI, Admin ()
Get User Access(2): 04 02 01 0f No access (syq)
Get User Access(3): 04 02 01 34 IPMI, Admin (admin)
Get User Access(4): 04 02 01 0f No access ()
pefconfig: completed successfully
[EMAIL PROTECTED] ~]# ipmiutil serial
ipmiutil ver 1.8
tmconfig ver 1.39
-- BMC version 0.56, IPMI version 2.0
Code 0 SEL Ver 2 Support 15
tmconfig: GetSerEntry for channel 4 ...
Serial Param(0) Set in progress: 00
Serial Param(1) Auth type support: 15 None MD5 Pswd
Serial Param(2) Auth type enables: 14 14 14 14 00
Serial Param(3) Connection Mode: 87
Serial Param(4) Sess Inactiv Timeout: 00
Serial Param(5) Channel Callback: 00 00 ff ff ff
Serial Param(6) Session Termination: 03
Serial Param(7) IPMI Msg Comm: 60 07 RTS/CTS, DTR, 19.2k
Serial Param(8) Mux Switch: 16 08
Serial Param(9) Modem Ring Time: 3f 00
Serial Param(10) Modem Init String: 01 ATE1Q0V1X4&D2&C1
Serial Param(11) Modem Escape Seq: +++
Serial Param(12) Modem Hangup Seq: ATH
Serial Param(13) Modem Dial Command: ATD
Serial Param(14) Page Blackout Interval: 00
Serial Param(15) Community String: public
Serial Param(16) Num of Alert Dest: 08
Serial Param(17) Destination Info: 01 00 05 03 00
Serial Param(17) Destination Info: 02 00 05 03 00
Serial Param(17) Destination Info: 03 00 05 03 00
Serial Param(17) Destination Info: 04 00 05 03 00
Serial Param(17) Destination Info: 05 00 05 03 00
Serial Param(17) Destination Info: 06 00 05 03 00
Serial Param(17) Destination Info: 07 00 05 03 00
Serial Param(17) Destination Info: 08 00 05 03 00
Serial Param(18) Call Retry Interval: 3c
Serial Param(19) Destination Comm Settings: 01 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 02 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 03 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 04 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 05 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 06 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 07 00 07 no_flow, 8N1, 19.2k
Serial Param(19) Destination Comm Settings: 08 00 07 no_flow, 8N1, 19.2k
Serial Param(20) Number Dial Strings: 06
Serial Param(21) Dest Dial String: 01 01
Serial Param(21) Dest Dial String: 02 01
Serial Param(21) Dest Dial String: 03 01
Serial Param(21) Dest Dial String: 04 01
Serial Param(21) Dest Dial String: 05 01
Serial Param(21) Dest Dial String: 06 01
Serial Param(22) Number Dest IP Addrs: 04
Serial Param(23) Dest IP Address: 01 0 0 0 0
Serial Param(23) Dest IP Address: 02 0 0 0 0
Serial Param(23) Dest IP Address: 03 0 0 0 0
Serial Param(23) Dest IP Address: 04 0 0 0 0
Serial Param(29) Terminal Mode Config: 66 11
Channel Access Mode(4=Ser): 2b 04 Access = Shared, PEF Alerts Disabled
Get User Access (1): 04 01 01 14 IPMI, Admin ()
Get User Access (2): 04 01 01 0f No access (syq)
Get User Access (3): 04 01 01 0f No access (admin)
Get User Access (4): 04 01 01 0f No access ()
Get Serial MUX Status: 04
Get Boot Options(3): 01 03 0c
tmconfig: completed successfully
Thanks & Regards,
Song Youquan
OTC-Beijing
Intel SSG/SSD
MOB: 13681289076
TEL: 010-82611515-1326
INET: 8-758-1326
LOC: Raycom 6W062
________________________________
From: Cress, Andrew R
Sent: 2007年9月7日 21:33
To: Song, Youquan
Subject: RE: [Ipmitool-devel] IPMI SOL failed on Intel Harwich
Song Youquan,
Hmmm. I'm guessing that there are configuration problems.
Or, there were some recent firmware changes for iBMC for SOL padding
compatibility, but I don't think Harwich has the new iBMC.
Can you send me the output of "ipmiutil lan" and "ipmiutil serial"?
See http://ipmiutil.sf.net
The same parameters can be read from ipmitool with several more commands, but
this will give the complete set of configuration parameters.
I am assuming that the BIOS has Serial Console redirection enabled?
FYI, Here are some tips for setting up SOL:
http://telcoserv.so.intel.com/ras/tips.htm
Andy
________________________________
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Song, Youquan
Sent: Friday, September 07, 2007 1:13 AM
To: ipmitool-devel@lists.sourceforge.net
Cc: Song, Youquan
Subject: [Ipmitool-devel] IPMI SOL failed on Intel Harwich
Ipmitool can work round, however, IPMI SOL can not work round. Please give me
some help to solve it??
[EMAIL PROTECTED] ~]# ipmitool -I lanplus -H $IP -U $USER -P $PASSWORD -v -o
intelplus sol activate
Error activating SOL payload: Invalid data field in request
[EMAIL PROTECTED] ~]# ipmitool -I lanplus -H $IP -U $USER -P $PASSWORD -v -o
intelplus sol info
Info: SOL parameter 'Payload Channel (7)' not supported - defaulting to 0x0e
Info: SOL parameter 'Payload Port (8)' not supported - defaulting to 623
Set in progress : set-complete
Enabled : true
Force Encryption : true
Force Authentication : true
Privilege Level : ADMINISTRATOR
Character Accumulate Level (ms) : 20
Character Send Threshold : 50
Retry Count : 6
Retry Interval (ms) : 20
Volatile Bit Rate (kbps) : IPMI-Over-Serial-Setting
Non-Volatile Bit Rate (kbps) : 19.2
Payload Channel : 14 (0x0e)
Payload Port : 623
I set force-encryption = false and force-authentication=false, and I also get
the same result as "Error activating SOL payload: Invalid data field in
request"
Harwich with Intel Xeon 3.4G X 4 CPUs, BIOS: HW_P11_56_39_xx_Build01.
[EMAIL PROTECTED] ~]# lsmod | grep ipmi
ipmi_devintf 44432 0
ipmi_si 72336 0
ipmi_msghandler 70420 2 ipmi_devintf,ipmi_si
BIOS, I already set "Console Redirection [Enable] "
dmidecode : to show IPMI version information
IPMI Device Information
Interface Type: KCS (Keyboard Control Style)
Specification Version: 2.0
I2C Slave Address: 0x10
NV Storage Device: Not Present
Base Address: 0x0000000000000CA2 (I/O)
Register Spacing: Successive Byte Boundaries
Thanks & Regards,
Song Youquan
OTC-Beijing
Intel SSG/SSD
MOB: 13681289076
TEL: 010-82611515-1326
INET: 8-758-1326
LOC: Raycom 6W062
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Ipmitool-devel mailing list
Ipmitool-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
