On Thu, 13 Dec 2007, Massimo Gaggero wrote:
> ok, > sensor has been reinitialized, but commounication not. > I can issue a 'sensor' command and the answer seems correct > but non lan channel is available and after 'bmc reset cold' on IBM x3455. > > Can this command reset BMC eprom where are stored informations on how to > contact the NIC and > BMC is not more able to find it? > > Another thing that I remember is that all onboard NIC (Broadcom > Nextreme) have Onboard Management Software > disabled due to a conflict to linux module 8021q. Can this make BMC > unable to find lan channel? After a cold reset? I think the cold reset will set its state back to the HW settings. In other words if you have configured it via ipmitool and those configs are not reflected in the BMC HW settings, then I believe after a cold reset the BMC goes back to its settings. In summary, make sure you BMC settings are correct. MAtthias > > Regards, > Massimo. > > # ipmitool sensor > Fan 1 Tach | 3225.000 | RPM | ok | 750.000 | > 1350.000 | 1950.000 | na | na | na > Fan 2 Tach | 2925.000 | RPM | ok | 750.000 | > 1350.000 | 1950.000 | na | na | na > Fan 3 Tach | 2925.000 | RPM | ok | 750.000 | > 1350.000 | 1950.000 | na | na | na > SYS PWR Monitor | 0x0 | discrete | 0x0080| na | > na | na | na | na | na > Watchdog | 0x0 | discrete | 0x0080| na | > na | na | na | na | na > Planar 1.2V | 1.210 | Volts | ok | na | > 1.060 | na | na | 1.310 | na > Planar 3.3V | 3.273 | Volts | ok | na | > 2.960 | na | na | 3.606 | na > Planar 5V | 5.284 | Volts | ok | na | > 4.726 | na | na | 5.780 | na > Planar VBAT | 3.116 | Volts | ok | na | > na | 2.234 | 3.734 | na | na > Ambient Temp | 20.000 | degrees C | ok | 64.000 | > na | 64.000 | -128.000 | na | na > CPU 1 Temp | 35.000 | degrees C | ok | na | > na | na | 85.000 | 90.000 | 95.000 > CPU 2 Temp | 39.000 | degrees C | ok | na | > na | na | 85.000 | 90.000 | 95.000 > FP Cable Detect | 0x0 | discrete | 0x0280| na | > na | na | na | na | na > CPU 1 Status | 0x0 | discrete | 0x8080| na | > na | na | na | na | na > CPU 2 Status | 0x0 | discrete | 0x8080| na | > na | na | na | na | na > NMI State | 0x0 | discrete | 0x0080| na | > na | na | na | na | na > SEL Fullness | 16.000 | messages | ok | 10.000 | > 20.000 | 30.000 | 75.000 | 90.000 | 100.000 > ABR Status | na | discrete | na | na | > na | na | na | na | na > CPU 1 Bad VID | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > CPU 2 Bad VID | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > VRD 1 Status | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > VRD 2 Status | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > PCI Slot Faults | 0x0 | discrete | 0x0080| na | > na | na | na | na | na > PS 1 Status | 0x0 | discrete | 0x0080| na | > na | na | na | na | na > PS 1 Fan Fault | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > PS1 Therm Fault | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > Unknown Souce | 0x0 | discrete | 0x0080| na | > na | na | na | na | na > CPU 1 Prochot | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > CPU 2 Prochot | 0x0 | discrete | 0x0180| na | > na | na | na | na | na > > # ipmitool lan print > Invalid channel: 255 > # ipmitool lan print 1 > Channel 1 is not a LAN channel > # > > > Amit Kumar ha scritto: > > > > > > Hi Massimo, > > > > If you refer to table 20.2 in ipmi specification v2.0, it is mentioned > > that user should not depend on response of the command. > > > > Cold reset command resets the communication, event and sensor functions. > > > > So could you check if sensor or communication has been reinitialized? > > If yes, then it means , it works fine. > > > > Regards > > Amit > > > > -- > ____ ____ ____ _ _ > / ___)| __ \/ ___)/ /| | Dott. Massimo Gaggero > | (___ | /\___ \\__ | Expert Software Engineer > \____)|_|\_\(____/ |_| Advanced Computing and Communications - > Distributed Computing > E-mail: [EMAIL PROTECTED] Phone: +39 070 9250 329 > > > > ------------------------------------------------------------------------- > SF.Net email is sponsored by: > Check out the new SourceForge.net Marketplace. > It's the best place to buy or sell services > for just about anything Open Source. > http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace > _______________________________________________ > Ipmitool-devel mailing list > Ipmitool-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/ipmitool-devel > ------------------------------------------------------------------------- SF.Net email is sponsored by: Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ Ipmitool-devel mailing list Ipmitool-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
