Ok Steffen. Thank you very much for your immediate response. But I am sitting in a remote location. I cannot even see that machine manually :-((
Regards, Viswanath "Don't aim to be a slave in heaven, at least aim to be a king of hell" -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Steffen Grunewald Sent: Thursday, April 03, 2008 8:45 PM To: Viswanath Thangamuthu, Bangalore Cc: ipmitool-devel@lists.sourceforge.net Subject: Re: [Ipmitool-devel] Reg: IPMItool output On Thu, Apr 03, 2008 at 08:37:29PM +0530, Viswanath Thangamuthu, Bangalore wrote: > > Hi , > > > > I have installed Super micro V2.0 card on our system to monitor system > health. But I wondered that, processor fan is showing 0 RPM.There are > couple of fan entries and my interest is about processor fan only. why > fan4 is only showing some non-zero value?. What is fan4?. Pls clarify me > on this. Thanks in advance. > > > > #ipmitool sdr list > > > > CPU | 22 degrees C | ok > CPU Core | 1.22 Volts | ok > DIMM | 1.81 Volts | ok > 3.3V | 3.36 Volts | ok > 5V | 4.90 Volts | ok > 5VSB | 4.94 Volts | ok > 12V | 11.71 Volts | ok > -12V | -12.38 Volts | ok > Battery | 3.25 Volts | ok > FAN1 | 0 RPM | ok > FAN2 | 0 RPM | ok > FAN3 | 0 RPM | ok > FAN4 | 5130 RPM | ok > FAN5 | 0 RPM | ok > FAN6/CPU | 0 RPM | ok > Intrusion | 0 unspecified | ok > Power Supply | 0 unspecified/u | cr The mainboard has 5 sockets/connectors for fans (at least, since only those which provide a sensor pin are counted). The mapping of fans to sockets (and therefore, sdrs) is done by *wires*. The only way to find out is to open the case and have a look (and get the mainboard manual to identify the connectors) S -- Steffen Grunewald * MPI Grav.Phys.(AEI) * Am Mühlenberg 1, D-14476 Potsdam Cluster Admin * http://pandora.aei.mpg.de/merlin/ * http://www.aei.mpg.de/ * e-mail: steffen.grunewald(*)aei.mpg.de * +49-331-567-{fon:7233,fax:7298} No Word/PPT mails - http://www.gnu.org/philosophy/no-word-attachments.html ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ Ipmitool-devel mailing list Ipmitool-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ipmitool-devel DISCLAIMER: ----------------------------------------------------------------------------------------------------------------------- The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only. It shall not attach any liability on the originator or HCL or its affiliates. Any views or opinions presented in this email are solely those of the author and may not necessarily reflect the opinions of HCL or its affiliates. Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have received this email in error please delete it and notify the sender immediately. Before opening any mail and attachments please check them for viruses and defect. ----------------------------------------------------------------------------------------------------------------------- ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ Ipmitool-devel mailing list Ipmitool-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
