Yes. If you have not installed your version of weston correctly it could cause any number of problems.
From: IVI [mailto:[email protected]] On Behalf Of Yang Andy Sent: Monday, September 15, 2014 6:25 PM To: Ylinen, Mikko Cc: [email protected]; Liu, DeyiX Subject: RE: [TizenCommon]Crosswalk launch failed Hi Mikko >What is the hardware you're using? VTC1010. But i customize TizenCommon image,i use weston1.4. Is there any possibility that weston will result in crosswalk launch fail? Best regards. Andy ________________________________ Date: Thu, 11 Sep 2014 13:42:16 +0300 Subject: Re: [TizenCommon]Crosswalk launch failed From: [email protected]<mailto:[email protected]> To: [email protected]<mailto:[email protected]> CC: [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]> What is the hardware you're using? On Thu, Sep 11, 2014 at 12:20 PM, Yang Andy <[email protected]<mailto:[email protected]>> wrote: Hi everyone I tried to use open_app to launch app,it failed to start up app. I analyzed the limited error log and found that process stoped at xwalk [NavigationControllerImpl::LoadURLWithParams]. Could anyone give me some advice? [Error Info] localhost xwalk[548]: [0911/020431:INFO:navigation_controller_impl.cc(778)] NavigationControllerImpl::LoadURLWithParams localhost sh[314]: Couldn't call 'Launch' method: GDBus.Error:org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus) localhost sh[314]: launch_application 1 localhost systemd[258]: xwalk.service: main process exited, code=killed, status=11/SEGV localhost systemd[258]: Unit xwalk.service entered failed state. Best regards. Andy ________________________________ From: [email protected]<mailto:[email protected]> To: [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]> Subject: RE: [TizenCommon]Crosswalk launch failed Date: Tue, 9 Sep 2014 01:56:17 +0000 Hi everyone >Andy please use open_app binary to start an app. >open_app <appid> I tried to use open_app to launch app,it failed and the result is the same as using xwalk-launch. I analyzed the limited error log and found that process stoped at xwalk [ApplicationService::Launch]. Could anyone give me some advice? Best regards. Andy ________________________________ Date: Thu, 4 Sep 2014 11:42:17 +0200 Subject: Re: [TizenCommon]Crosswalk launch failed From: [email protected]<mailto:[email protected]> To: [email protected]<mailto:[email protected]> CC: [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]>; [email protected]<mailto:[email protected]> Hi all, Andy please use open_app binary to start an app. open_app <appid> Thanks 2014-09-03 11:50 GMT+02:00 Ylinen, Mikko <[email protected]<mailto:[email protected]>>: On Tue, Sep 2, 2014 at 8:39 AM, Yang Andy <[email protected]<mailto:[email protected]>> wrote: Hi everyone I want to launch Crosswalk at TizenCommon platform. But when use command to launch Crosswalk from wayland terminal,i run into fatal error below. What's the command you are using? xwalk-launcher [<URL>|<appid>]? -- Mikko _______________________________________________ IVI mailing list [email protected]<mailto:[email protected]> https://lists.tizen.org/listinfo/ivi -- Baptiste DURAND Eurogiciel Vannes/FR
_______________________________________________ IVI mailing list [email protected] https://lists.tizen.org/listinfo/ivi
