On Friday 02 December 2005 20:00, Brendan Hoar wrote: > Using KnoppMyth R5A26, upgrading to 0.4.1 svn as of today (see > below), ivtv could not find the firmware. I added the following > module options, which appeared to be recognized correctly in the > example output below: > > options ivtv ivtv_efw=/lib/modules/ivtv-fw-enc.bin > options ivtv ivtv_dfw=/lib/modules/ivtv-fw-dec.bin > > I also tried adding the following, but cx25840 didn't recognize it as > valid, even though modules.txt indicates cx25840_fw is valid: > > options cx25840 cx25840_fw=/lib/modules/HcwMakoA.ROM > > In any case, ivtv still reports that it cannot find the firmware at > /lib/modules/ivtv-fw-enc.bin even though it is there. > > Anyone know why it's still complaining? > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.1 (development snapshot compiled on Fri Dec 2 > 13:02:54 2005) > loading > ivtv: Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) > ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 17 > tveeprom: ivtv version > tveeprom: Hauppauge: model = 48132, rev = K168, serial# = 7519667 > tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio processor = MSP4448 (type = 1b) > tveeprom: decoder processor = SAA7115 (type = 13) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > tuner (ivtv): chip found at addr 0xc2 i2c-bus cx88[0] > tuner: type set to 52 (Thomson DDT 7610 (ATSC/NTSC)) by cx88[0] > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] > saa7127 2-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] > msp3400 2-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio > mode=simpler > msp3400 2-0040: msp34xxg daemon started > ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40] > tda9887 0-0043: (ivtv) chip found @ 0x86 (cx88[0]) > tda9887 2-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] > ivtv0: unable to open firmware /lib/modules/ivtv-fw-enc.bin > ivtv0 warning: failed loading encoder firmware > ivtv0 warning: Error loading firmware -3! > ivtv0: Error -3 initializing firmware. > ivtv0: Error -12 on initialization > ivtv: probe of 0000:00:06.0 failed with error -12
You should put the firmware in the hotplug directory. See: http://www.ivtvdriver.org/index.php/Firmware#Kernels_with_firmware_hotplug Hans _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
