Is possible to configure Yuan Falcon2 PG600-2 Card under linux (I use SuSE 9.3)? Thanks! This is the IVTV debug message: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.3 (tagged release) loading ivtv: Linux version: 2.6.11.4-21.10-default K7 REGPARM gcc-3.3 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Unknown card: vendor/device: 4444/0016 ivtv0: subsystem vendor/device: ffab/0600 ivtv0: cx23416 based ivtv0: Defaulting to WinTV PVR 250 card ivtv0: Please mail the vendor/device and subsystem vendor/device IDs and what kind of ivtv0: card you have to the ivtv-devel mailinglist (www.ivtvdriver.org) ivtv0: Prefix your subject line with [UNKNOWN CARD]. ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11 ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] msp3400: error while reading chip version tveeprom: Encountered bad packet header [ff]. Corrupt or not a Hauppauge eeprom. ivtv0 warning: i2c client addr: 0x21 not found for command 0x8004646b! ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0 warning: i2c client addr: 0x00 not found for command 0x40047401! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x21 not found for command 0xc0045627! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40086d11! ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! ivtv0 warning: i2c client addr: 0x00 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045613! ivtv0 warning: i2c client addr: 0x00 not found for command 0x402c5639! ivtv0 warning: i2c client addr: 0x40 not found for command 0x402c5639! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045612! ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! ivtv0: Initialized WinTV PVR 250, card #0 ivtv: ==================== END INIT IVTV ====================
_______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
