It's supported in ivtv-0.6.0 which is for the new 2.6.16 kernel ONLY. If
it is as easy as I think it is then I'll try to add it to the upcoming
0.4.4 too to support it for older kernels.
Hans
On Thursday 23 March 2006 02:14, root wrote:
> Is possible to configure Yuan Falcon2 PG600-2 Card under linux (I use
> SuSE 9.3)?
> Thanks!
> This is the IVTV debug message:
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.3 (tagged release) loading
> ivtv: Linux version: 2.6.11.4-21.10-default K7 REGPARM gcc-3.3
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Unknown card: vendor/device: 4444/0016
> ivtv0: subsystem vendor/device: ffab/0600
> ivtv0: cx23416 based
> ivtv0: Defaulting to WinTV PVR 250 card
> ivtv0: Please mail the vendor/device and subsystem vendor/device IDs
> and what kind of
> ivtv0: card you have to the ivtv-devel mailinglist
> (www.ivtvdriver.org) ivtv0: Prefix your subject line with [UNKNOWN
> CARD].
> ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> msp3400: error while reading chip version
> tveeprom: Encountered bad packet header [ff]. Corrupt or not a
> Hauppauge eeprom.
> ivtv0 warning: i2c client addr: 0x21 not found for command
> 0x8004646b! ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers
> (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208
> buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total)
> ivtv0: Create encoder radio stream
> ivtv0 warning: i2c client addr: 0x00 not found for command
> 0x40047401! ivtv0 warning: i2c client addr: 0x21 not found for
> command 0x40085618! ivtv0 warning: i2c client addr: 0x21 not found
> for command 0xc0045627! ivtv0 warning: i2c client addr: 0x40 not
> found for command 0x40086d11! ivtv0 warning: i2c client addr: 0x40
> not found for command 0x80287610! ivtv0 warning: i2c client addr:
> 0x40 not found for command 0x40287611! ivtv0 warning: i2c client
> addr: 0x00 not found for command 0x40085618! ivtv0 warning: i2c
> client addr: 0x40 not found for command 0x40085618! ivtv0 warning:
> i2c client addr: 0x21 not found for command 0x40085618! ivtv0
> warning: i2c client addr: 0x40 not found for command 0x80287610!
> ivtv0 warning: i2c client addr: 0x40 not found for command
> 0x40287611! ivtv0 warning: i2c client addr: 0x21 not found for
> command 0x40045613! ivtv0 warning: i2c client addr: 0x00 not found
> for command 0x402c5639! ivtv0 warning: i2c client addr: 0x40 not
> found for command 0x402c5639! ivtv0 warning: i2c client addr: 0x21
> not found for command 0x40045612! ivtv0 warning: i2c client addr:
> 0x40 not found for command 0x80287610! ivtv0 warning: i2c client
> addr: 0x40 not found for command 0x40287611! ivtv0: Initialized WinTV
> PVR 250, card #0
> ivtv: ==================== END INIT IVTV ====================
>
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
