Hi,
I just bought a WinTV PVR150, and I followed the instructions for Ubuntu
on the ivtvdriver website (using Ubuntu Breezy). Everything seemed to
work fine.
THe problem is that my tuner remains unrecognized. Through VLC, I used
to have static, and somehow, I managed to change the channel once. I
can see that one channel, and the sound is fine. I can also record
(cat /dev/video0 > test.mpg) and that is fine too (again, for that one
channel). I can adjust settings (height, width, bitrate, etc) through
ivtvctl. ivtv-tune *says* that I have changed channels when trying to
do so, but with VLC/Mplayer, it is always the same channel. I'm
baffled.
Here's my dmesg output.
[4294705.303000] ivtv: ==================== START INIT IVTV
====================
[4294705.303000] ivtv: version 0.4.3 (tagged release) loading
[4294705.303000] ivtv: Linux version: 2.6.12-10-386 386 gcc-3.4
[4294705.303000] ivtv: In case of problems please include the debug
info between
[4294705.303000] ivtv: the START INIT IVTV and END INIT IVTV lines,
along with
[4294705.303000] ivtv: any module options, when mailing the ivtv-users
mailinglist.
[4294705.306000] ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
[4294705.307000] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[4294705.307000] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC2] ->
GSI 17 (level, low) -> IRQ 17
[4294705.307000] ivtv0: Unreasonably low latency timer, setting to 64
(was 32)
[4294705.322000] ivtv0: i2c attach to card #0 ok [client=tveeprom,
addr=50]
[4294705.370000] tveeprom: Hauppauge: model = 26132, rev = C599, serial#
= 8905850
[4294705.370000] tveeprom: tuner = <unknown> (idx = 99, type =
-1070989888)
[4294705.370000] tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
[4294705.370000] tveeprom: audio_processor = TDA9850 (type = 3)
[4294705.396000] ivtv0: i2c attach to card #0 ok [client=(tuner unset),
addr=61]
[4294705.397000] tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
[4294705.816000] cx25840 2-0044: ivtv driver
[4294705.816000] cx25840 2-0044: cx25841-23 found @ 0x88 (ivtv i2c
driver #0)
[4294708.022000] cx25840 2-0044: loaded v4l-cx25840.fw firmware (12282
bytes)
[4294708.069000] ivtv0: i2c attach to card #0 ok [client=cx25840,
addr=44]
[4294708.111000] wm8775 2-001b: ivtv driver
[4294708.111000] wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
[4294708.117000] ivtv0: i2c attach to card #0 ok [client=wm8775,
addr=1b]
[4294708.827000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144
bytes)
[4294709.037000] ivtv0: Encoder revision: 0x02050032
[4294709.037000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
[4294709.038000] ivtv0: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
[4294709.039000] ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
[4294709.040000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
[4294709.041000] ivtv0: Create encoder radio stream
[4294709.107000] tuner 2-0061: tuner type not set
[4294709.224000] ivtv0: Initialized WinTV PVR 150, card #0
[4294709.224000] ivtv: ==================== END INIT IVTV
====================
Here's my lspci -v for the card.
0000:01:07.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 8003
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <available only to root>
I tried changing the firmware HcwMakoA.ROM from the Ubuntu guide on
ivtvdriver.org for the one that came on my CD (it only has HcwMakoB.ROM
and HcwMakoC.ROM, so I tried C), but that didn't make a difference
either.
Any suggestions?
Thanks.
Vince
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
