Hello, The card worked OK with 0.4.x releases with 2.6.15, but now the tuner is broken. The card is detected,
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.1 (tagged release) loading ivtv: Linux version: 2.6.16-1-k7 K7 gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 201 tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 0-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 0-0044: loaded v4l-cx25840.fw firmware (14264 bytes) wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 2984847 tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX25841 (idx 35) tveeprom 0-0050: decoder processor is CX25841 (idx 28) tveeprom 0-0050: has no radio, has IR remote ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 0-0061: type set to 50 (TCL 2002N) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== Which is the same as before (with 2.6.15 kernel), but the status is messed up. When I set the tuner to channel 6, I get, ivtv0: ================= START STATUS CARD #0 ================= tveeprom 0-0050: Hauppauge model 26032, rev C199, serial# 2984847 tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX25841 (idx 35) tveeprom 0-0050: decoder processor is CX25841 (idx 28) tveeprom 0-0050: has no radio, has IR remote tuner 0-0061: Tuner mode: radio tuner 0-0061: Frequency: 0.08 MHz tuner 0-0061: Standard: 0x0000b000 tuner 0-0061: Signal strength: 32768 tuner 0-0061: Stereo: yes cx25840 0-0044: Video signal: not present cx25840 0-0044: Detected format: NTSC-M cx25840 0-0044: Detected audio mode: forced mode cx25840 0-0044: Detected audio standard: forced audio standard cx25840 0-0044: Audio muted: no cx25840 0-0044: Audio microcontroller: running cx25840 0-0044: Configured audio standard: BTSC cx25840 0-0044: Configured audio mode: undefined cx25840 0-0044: Specified standard: NTSC-M cx25840 0-0044: Specified video input: Composite 7 cx25840 0-0044: Specified audio input: Tuner (In8) cx25840 0-0044: Specified audioclock freq: 48000 Hz cx25840 0-0044: Preferred audio mode: stereo cx25840 0-0044: Selected 65 MHz format: system DK cx25840 0-0044: Selected 45 MHz format: chroma wm8775 0-001b: Input: 2 ivtv0: ================== END STATUS CARD #0 ================== This is after setting the frequency to 83.250. It seems the frequency gets chopped by a factor of 1000. Setting frequency to 83250 doesn't help, though the Frequency in status is then 83.250 Is it possible to change the tuner into "normal" mode? - Adam _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
