Hi, i installed opensuse 10.1, kernel 2.6.16.16 and ivtv-0.6.2.
I followed the instructions and ivtv gets loaded. I attached the part in the output of "dmesg" that is related to ivtv. When i set up my Hauppauge PVR350: ivtvctl -c bitrate=4000000 ivtv-tune -t europe-west -c S25 # BBC cat /dev/video >file.mpg <Ctrl-C> "mplayer file.mpg" plays for the time that i capured, but the output is just "white noise", the station seems to be not set correct. Also the dimensions (720 x 576) is fine. Just two days ago i ran an older distribution with older ivtv-driver and also captured from "S25". That worked fine. Whenever i try to set the channel: ivtv-tune -t europe-west -c S25 # BBC In /var/log/messages i get: ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c What went wrong here? Best regards, Torsten.
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.2 (tagged release) loading ivtv: Linux version: 2.6.16.16-default K7 REGPARM gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 177 PCI: Via IRQ fixup for 0000:00:10.3, from 0 to 1 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.3: irq 177, io base 0x00009000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Linux agpgart interface v0.101 (c) Dave Jones ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:12.0, from 0 to 9 eth0: VIA Rhine II at 0x18800, 00:13:d4:29:fa:00, IRQ 185. eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 0020. sata_via 0000:00:0f.0: version 1.1 ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 169 PCI: Via IRQ fixup for 0000:00:0f.0, from 0 to 9 sata_via 0000:00:0f.0: routed to hard irq line 9 ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xB000 irq 169 ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xB008 irq 169 usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice hub 3-1:1.0: USB hub found ata1: SATA link down (SStatus 0) scsi0 : sata_via hub 3-1:1.0: 4 ports detected ata2: SATA link down (SStatus 0) scsi1 : sata_via ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based) ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 193 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: Failed to load module tveeprom tveeprom 1-0050: Hauppauge model 48139, rev K257, serial# 7735007 tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 1-0050: audio processor is MSP4418 (idx 25) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has IR remote ivtv0: Failed to load module tuner ivtv0: Failed to load module tda9887 saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) ivtv0: Failed to load module msp3400 usb 3-1.1: new full speed USB device using uhci_hcd and address 3 usb 3-1.1: configuration #1 chosen from 1 choice Initializing USB Mass Storage driver... scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02040011 ivtv0: Decoder revision: 0x02020023 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv0: Create decoder VOUT stream ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total) ivtv0: unable to open firmware v4l-cx2341x-init.mpg ivtv0: did you put the firmware in the hotplug firmware directory? ivtv0: failed to read mpeg decoder initialisation file v4l-cx2341x-init.mpg ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! ivtv0: i2c addr 0x40 not found for command 0x40086d11! ivtv0: i2c addr 0x40 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ==================== END INIT IVTV ====================
_______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
