> I see no mention of the newi2c=0 module option. Run: > > modprobe ivtv newi2c=0
sorry head like a seive. modified modprobe.conf: options ivtv newi2c=0 tuner=50,-1 and modprobed it as follows: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.2 (tagged release) loading ivtv: Linux version: 2.6.16-1.2122_FC5 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== then a soft 'reboot' ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.2 (tagged release) loading ivtv: Linux version: 2.6.16-1.2122_FC5 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 18 tveeprom 1-0050: Hauppauge model 26132, rev F0B2, serial# 9400151 tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 4) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 1-0061: type set to 50 (TCL 2002N) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== will do some more of my reboot 'hammering' and let you know... _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
