Andy, More updates: Using TV Tuner input I could get audio in some channel, however no video using TV Tuner. Thanks and best regards, Rajesh
On Thu, Nov 12, 2009 at 9:04 PM, Rajesh Padalia <[email protected]> wrote: > Hi Andy, > I could resolve issue of óut of sync' by setting video standard to PAL > Thanks... > Rajesh > > On Thu, Nov 12, 2009 at 8:34 PM, Rajesh Padalia > <[email protected]> wrote: >> Hi Andy, >> 1. $ v4l2-ctl --log-status: >> Status Log: >> >> ivtv0: ================= START STATUS CARD #0 ================= >> ivtv0: Version: 1.4.1 Card: Yuan PG600, Diamond PVR-550 >> cx25840 1-0044: Video signal: present >> cx25840 1-0044: Detected format: PAL-BDGHI >> cx25840 1-0044: Specified standard: NTSC-M >> cx25840 1-0044: Specified video input: Composite 1 >> cx25840 1-0044: Specified audioclock freq: 48000 Hz >> cx25840 1-0044: Detected audio mode: mono >> cx25840 1-0044: Detected audio standard: no detected audio standard >> cx25840 1-0044: Audio muted: no >> cx25840 1-0044: Audio microcontroller: stopped >> cx25840 1-0044: Configured audio standard: automatic detection >> cx25840 1-0044: Configured audio system: BTSC >> cx25840 1-0044: Specified audio input: External >> cx25840 1-0044: Preferred audio mode: stereo >> tda9887 1-0043: Data bytes: b=0xd4 c=0x30 e=0x44 >> tuner 1-0060: Tuner mode: analog TV >> tuner 1-0060: Frequency: 67.25 MHz >> tuner 1-0060: Standard: 0x00001000 >> ivtv0: Video Input: Composite 1 >> ivtv0: Audio Input: Line In 1 >> ivtv0: Tuner: TV >> ivtv0: Stream: MPEG-2 Program Stream >> ivtv0: VBI Format: No VBI >> ivtv0: Video: 720x480, 30 fps >> ivtv0: Video: MPEG-2, 4x3, Variable Bitrate, 6000000, Peak 8000000 >> ivtv0: Video: GOP Size 15, 2 B-Frames, GOP Closure >> ivtv0: Audio: 48 kHz, MPEG-1/2 Layer II, 224 kbps, Stereo, No >> Emphasis, No CRC >> ivtv0: Spatial Filter: Manual, Luma 1D Horizontal, Chroma 1D Horizontal, 0 >> ivtv0: Temporal Filter: Manual, 8 >> ivtv0: Median Filter: Off, Luma [0, 255], Chroma [0, 255] >> ivtv0: Status flags: 0x00200000 >> ivtv0: Stream encoder MPG: status 0x0118, 0% of 4096 KiB (128 buffers) in >> use >> ivtv0: Stream encoder YUV: status 0x0000, 0% of 2048 KiB (64 buffers) in >> use >> ivtv0: Stream encoder VBI: status 0x0000, 0% of 1040 KiB (61 buffers) in >> use >> ivtv0: Stream encoder PCM: status 0x0000, 0% of 324 KiB (72 buffers) in use >> ivtv0: Read MPG/VBI: 19052480/0 bytes >> ivtv0: ================== END STATUS CARD #0 ================== >> >> 2. The one close to crystal is : 74HC4053D, AG124 29, URO 0348D >> The other one is: 5333KZ, GZ0337 >> >> 3. I have '/lib/firmware/v4l-cx25840.fw' in my Fedora distro >> >> Today I got picture which seems to be out of sync. >> >> Thank you, >> >> Rajesh >> >> >> On Thu, Nov 12, 2009 at 2:18 AM, Andy Walls <[email protected]> wrote: >>> On Wed, 2009-11-11 at 19:55 +0300, Rajesh Padalia wrote: >>>> Hi Andy, >>>> It works! I was able to capture video. I am yet to get Audio. Any idea? >>>> ------------------------------- >>> >>> 1. Please provide the output of >>> >>> $ v4l2-ctl --log-status >>> >>> while capturing TV. >>> >>> 2. Also could you provide the chip numbers from the two black chips >>> next to the end of the metal tuner can just above the 27.00 MHz crystal? >>> I can't read them from the photograph. One looks like it has a >>> "Philips" logo, but I can't tell much else. >>> >>> 3. Make sure you have the firmware for the cx25843 chip in the proper >>> firmware directory for your distirbution. You will never get broadcast >>> audio without that firmware loaded into the CX25843. >>> >>> Regards, >>> Andy >>> >>>> --------------------------------------------------------------------------------------------- >>>> Thanks for your help. >>>> Rajesh >>>> >>>> On Wed, Nov 11, 2009 at 2:43 AM, Andy Walls <[email protected]> wrote: >>>> > On Tue, 2009-11-10 at 15:50 +0300, Rajesh Padalia wrote: >>>> >> Andy, >>>> >> I got message when I did modprobe ivtv card=7 tuner=57: >>>> >> "FATAL: Error inserting ivtv >>>> >> (/lib/modules/2.6.31.5-117.fc12.x86_64/kernel/drivers/media/video/ivtv/ivtv.ko): >>>> >> Unknown symbol in module, or unknown parameter (see dmesg)" >>>> > >>>> > Oops: that should have been >>>> > >>>> > # modprobe ivtv cardtype=7 tuner=57 >>>> > >>>> > Please try again. >>>> > >>>> > >>>> > For reference >>>> > >>>> > # modinfo ivtv >>>> > >>>> > will show you the possible module option names. >>>> > >>>> > Regards, >>>> > Andy >>>> > >>> >>> >>> >> > _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
