Does this help?
ivtvctl -j reg=0x6c,val=0xfa -d /dev/video16
Here is where I got that command
http://www.poptix.net/ivtv/Nov-2004/msg00342.html
Bob
On Sun, 5 Dec 2004, Kenneth Krekula wrote:
> Hi again.
>
> I finally got the new driver to load (using the 0.2.0-rc3) in Mandrake 10.1
> after following the advice here:
>
> http://www.byopvr.com/Journal+index-jop-browse-mode-view-id-112.html
>
> Now everything seems to load fine according to dmesg, but something still
> seems wrong as the tv-out just shows a green screen.
>
> This is the output of dmesg:
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.2.0 (rc3) loading
> ivtv: Linux version: 2.6.8.1-12mdk 686 gcc-3.4
> ivtv: In case of problems please include the debug info
> ivtv: between the START INIT IVTV and END INIT IVTV lines when
> ivtv: mailing the ivtv-devel mailinglist.
> ivtv: Autodetected WinTV PVR 350 card
> ivtv: Found an iTVC15 based chip
> ivtv: VIA PCI device: 0x0282 vendor: 0x1106
> tveeprom: Ignoring new-style parameters in presence of obsolete ones
> tveeprom: Hauppauge: model = 48139, rev = K257, serial# = 7597090
> tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38)
> tveeprom: tuner fmt = PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
> tveeprom: audio_processor = CS5331 (type = 9)
> ivtv: i2c attach [client=tveeprom[0],ok]
> ivtv: Tuner Type 38, Tuner formats 0x00400e17, Radio: yes, Model 0x00ad2557,
> Revision 0x00000001
> ivtv: PAL tuner detected
> ivtv: SECAM tuner detected
> ivtv: Radio detected
> tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv: i2c attach [client=(tuner unset),ok]
> saa7115: Ignoring new-style parameters in presence of obsolete ones
> saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
> saa7115: detecting saa7115 client on address 0x42
> saa7115: writing init values
> ivtv: i2c attach [client=saa7115[0],ok]
> saa7115: status: (1E) 0x00, (1F) 0xc0
> saa7127: Ignoring new-style parameters in presence of obsolete ones
> saa7127: video encoder driver version V 0.3 loaded
> saa7127: Selecting NTSC video Standard
> saa7127: Selecting S-Video+Composite
> saa7127: Turn WSS off
> saa7127: Widescreen Mode 4:3 Full Format
> saa7127: Selecting Normal Encoder Input
> saa7127: Enable Video Output
> ivtv: i2c attach [client=saa7127[0],ok]
> msp3400: Ignoring new-style parameters in presence of obsolete ones
> msp34xx: ivtv version
> msp34xx: init: chip=MSP3418W-B3, has NICAM support, simple (D) mode, simpler
> (G) no-thread mode
> msp34xx: $Id$ compiled on: Dec 5 2004 11:12:33
> ivtv: i2c attach [client=MSP3418W-B3,ok]
> ivtv: Encoder revision: 0x02040024
> ivtv: Encoder Firmware is buggy, use version 0x02040011
> ivtv: Decoder revision: 0x02020023
> ivtv: Configuring WinTV PVR 350 card with 9 streams
> ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
> ivtv: Registered v4l2 device, streamtype 0 minor 0
> ivtv: Create DMA stream 1 using 8 131072 byte buffers 1048576 kbytes total
> ivtv: Registered v4l2 device, streamtype 1 minor 32
> ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
> ivtv: Registered v4l2 device, streamtype 2 minor 224
> ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
> ivtv: Registered v4l2 device, streamtype 3 minor 24
> ivtv: Create stream 4
> ivtv: Registered v4l2 device, streamtype 4 minor 64
> ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total
> ivtv: Registered v4l2 device, streamtype 5 minor 16
> ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total
> ivtv: Registered v4l2 device, streamtype 6 minor 228
> ivtv: Create stream 7
> ivtv: Registered v4l2 device, streamtype 7 minor 232
> ivtv: Create DMA stream 8 using 16 65536 byte buffers 1048576 kbytes total
> ivtv: Registered v4l2 device, streamtype 8 minor 48
> ivtv: Setting Tuner 38
> tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c
> driver #0
> ivtv: Setting audio matrix to input 3, output 1
> ivtv: Switching standard to PAL.
> ivtv: ivtv_enc_thread: pid = 4740, itv = 0xf91164e0
> ivtv: ivtv_dec_thread: pid = 4741, itv = 0xf91164e0
> saa7115: decoder set norm PAL
> saa7115: set audio: 0x01
> saa7127: Setting Encoder Video Standard
> saa7127: Set PAL Video Mode
> saa7127: Selecting PAL video Standard
> ivtv: Initialized WinTV PVR 350, card #0
> ivtv: ==================== END INIT IVTV ====================
>
> I am using the firmware that is marked as "recommended" on the Ivtv Wiki
> site,
> but the driver still prints "Encoder Firmware is buggy, use version
> 0x02040011" ...?
>
> My /etc/modprobe.conf consists of these lines for Ivtv:
>
> alias char-major-81 vidodev
> alias char-major-81-0 ivtv
> options ivtv ivtv_debug=1
>
> I have tried to add "tda9887=1" to tha last line without seeing any
> difference
> (I also tried "tda9887=0" without success).
>
> As I live in Sweden,I would like to see PAL-B in the tveeprom message, but it
> says PAL-(D/K)
>
> Regards,
> Kenneth
>
>
> -------------------------------------------------------
> SF email is sponsored by - The IT Product Guide
> Read honest & candid reviews on hundreds of IT Products from real users.
> Discover which products truly live up to the hype. Start reading now.
> http://productguide.itmanagersjournal.com/
> _______________________________________________
> ivtv-devel mailing list
> [EMAIL PROTECTED]
> https://lists.sourceforge.net/lists/listinfo/ivtv-devel
>
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://productguide.itmanagersjournal.com/
_______________________________________________
ivtv-devel mailing list
[EMAIL PROTECTED]
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
