Hi, I'm trying to get my pvr 350 to work since days but without luck.
ivtv: unsupported module, tainting kernel. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.2 (c) loading ivtv: Linux version: 2.6.11.4-20a-default gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: ... running on kernel 2.6.11.4-20a-default ivtv: Setting some variables to invalid for detection ivtv: Scanning PCI bus.. ivtv: Found card #0 ivtv: User specified WinTV PVR 350 card ivtv: Found an iTVC15 based chip ivtv: base addr: 0xc8000000 ivtv: Enabling pci device ACPI: PCI interrupt 0000:05:08.0[A] -> GSI 18 (level, low) -> IRQ 233 ivtv: Bus Mastering Enabled.ivtv: 2051 (rev 1) at 05:08.0, ivtv: irq: 233, latency: 64, memory: 0xc8000000 ivtv: XXX PCI device: 0x005e vendor: 0x10de ivtv: attempting ioremap at 0xc8000000 len 0x00800000 ivtv: attempting ioremap at 0xc9000000 len 0x00800000 ivtv: attempting ioremap at 0xca000000 len 0x00010000 ivtv: activating i2c... ivtv: i2c init ivtv: setting scl and sda to 1 i2c-algo-bit.o: (0) scl=1, sda=1 i2c-algo-bit.o: (1) scl=1, sda=0 i2c-algo-bit.o: (2) scl=1, sda=1 i2c-algo-bit.o: (3) scl=0, sda=1 i2c-algo-bit.o: (4) scl=1, sda=1 i2c-algo-bit.o: ivtv i2c driver #0 passed test. ivtv: i2c client attach ivtv: i2c attach [client=tveeprom,ok] msp34xx: init: chip=MSP3418W-A2 +nicam +simple +simpler +radio mode=simple ivtv: i2c client attach ivtv: i2c attach [client=MSP3418W-A2,ok] msp3400: error while reading chip version tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c client attach ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c client attach ivtv: i2c attach [client=saa7115[1],ok] saa7115: status: (1E) 0x48, (1F) 0xc0 ivtv: Active card count: 1. msp3410: daemon started ivtv: Loaded module tveeprom ivtv: call_i2c_client ivtv: using client 0, addr 0x50 tveeprom: Hauppauge: model = 48134, rev = J321, serial# = 7196099 tveeprom: tuner = Philips FM1216 (idx = 21, type = 5) tveeprom: tuner fmt = PAL(B/G) (eeprom = 0x04, v4l2 = 0x00000007) tveeprom: audio_processor = CS5331 (type = 9) ivtv: Tuner Type 5, Tuner formats 0x00000007, Radio: yes, Model 0x00a93491, Revision 0x80344736 ivtv: Radio detected ivtv: Loaded module tuner ivtv: Loaded module saa7115 saa7127: unsupported module, tainting kernel. saa7127: Ignoring new-style parameters in presence of obsolete ones saa7127: video encoder driver version V 0.3 loaded saa7127: detecting saa7127 client on address 0x88 saa7127: Selecting NTSC video Standard saa7127: Selecting S-Video+Composite saa7127: Turn WSS off saa7127: Widescreen Mode 4:3 Full Format saa7127: Selecting Normal Encoder Input saa7127: Enable Video Output ivtv: i2c client attach ivtv: i2c attach [client=saa7127[0],ok] ivtv: Loaded module saa7127 ivtv: Loaded module msp3400 ivtv: Stopping VDM ivtv: Stopping AO ivtv: pinging (?) APU ivtv: Stopping VPU ivtv: Resetting Hw Blocks ivtv: Stopping SPU ivtv: Sleeping for 10ms ivtv: init Encoder SDRAM pre-charge ivtv: init Encoder SDRAM refresh to 1us ivtv: init Decoder SDRAM pre-charge ivtv: init Decoder SDRAM refresh to 1us ivtv: Sleeping for 600ms (600 recommended) ivtv: Card ready for firmware! ivtv: Loading encoder image ivtv: requesting firmware ivtv: firmware load failed ivtv: failed loading encoder firmware ivtv: Error loading firmware -3! ivtv: Error -3 initializing firmware. ivtv: i2c exit ivtv: i2c client detach ivtv: i2c detach [client=tveeprom,ok] ivtv: i2c client detach ivtv: i2c detach [client=MSP3418W-A2,ok] ivtv: i2c client detach ivtv: i2c detach [client=(tuner unset),ok] ivtv: i2c client detach ivtv: i2c detach [client=saa7115[1],ok] ivtv: i2c client detach ivtv: i2c detach [client=saa7127[0],ok] ivtv: releasing reg_mem ivtv: releasing dec_mem ivtv: releasing enc_mem ivtv: Error -12 on initialization ivtv-iTVC15_16_mpg2_encoder_card: probe of 0000:05:08.0 failed with error -12 ivtv: ==================== END INIT IVTV ==================== trying to load the saa with the test_image: insmod /lib/modules/2.6.11.4-20a-default/ivtv/saa7127.ko debug=2 insmod: error inserting '/lib/modules/2.6.11.4-20a-default/ivtv/saa7127.ko': -1 Unknown symbol in module saa7127: Ignoring new-style parameters in presence of obsolete ones load_module: err 0xfffffffffffffffe (dont worry) i also followed this thread: http://www.gossamer-threads.com/lists/ivtv/devel/17631?search_string=pvr%20350%20firmware;#17631 I also downloaed and extracted the recommended firmware... but without luck to load the firmware into the driver. what else can I do? kind regards uwe ------------------------------------------------------- This SF.Net email is sponsored by: NEC IT Guy Games. How far can you shotput a projector? How fast can you ride your desk chair down the office luge track? If you want to score the big prize, get to know the little guy. Play to win an NEC 61" plasma display: http://www.necitguy.com/?r=20 _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
