El Miércoles, 22 de Junio de 2005 17:17, Oscar Curero escribió: > Hi, > > Christoph Schulz <kristov AT arcor DOT de> write: > > I think this is the problem. You have a type 38 tuner but this is > > ignored because your tuner module is loaded with a "type=1" argument. > > Remove it and try it again. (I don't have any experiences with SuSE > > Linux, so I'm afraid I cannot tell you where to look for that option.) > > Ahh, yes, I know where to change it. It's in /etc/modprobe.conf.local > instead of /etc/modprobe.conf because this one is used by yast. Now the > output is like this: > > ivtv: unsupported module, tainting kernel. > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.3.2 (c) loading > ivtv: Linux version: 2.6.11.4-20a-default 586 REGPARM gcc-3.3 > ivtv: In case of problems please include the debug info > ivtv: between the START INIT IVTV and END INIT IVTV lines when > ivtv: mailing the ivtv-devel mailinglist. > ivtv: Autodetected WinTV PVR 350 card > ivtv: Found an iTVC15 based chip > ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 11 (level, low) -> IRQ 11 > ivtv: XXX PCI device: 0x5833 vendor: 0x1002 > i2c-algo-bit.o: (0) scl=1, sda=1 > i2c-algo-bit.o: (1) scl=1, sda=0 > i2c-algo-bit.o: (2) scl=1, sda=1 > i2c-algo-bit.o: (3) scl=0, sda=1 > i2c-algo-bit.o: (4) scl=1, sda=1 > i2c-algo-bit.o: ivtv i2c driver #0 passed test. > ivtv: i2c attach [client=unset,ok] > ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c > driver #0] ivtv: i2c attach [client=tveeprom,ok] > ivtv: i2c attach [client=saa7115[1],ok] > saa7127: detecting saa7127 client on address 0x88 > saa7127: Selecting NTSC video Standard > saa7127: Selecting S-Video+Composite > saa7127: Turn WSS off > saa7127: Widescreen Mode 4:3 Full Format > saa7127: Selecting Normal Encoder Input > saa7127: Enable Video Output > ivtv: i2c attach [client=saa7127[1],ok] > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv: i2c attach [client=(tuner unset),ok] > msp34xx: ivtv version > msp34xx: init: chip=MSP3418W-B3, has NICAM support, simple (D) mode, > simpler (G) no-thread mode > msp34xx: $Id$ compiled on: Mar 24 2005 00:28:39 > ivtv: i2c attach [client=MSP3418W-B3,ok] > tveeprom: Hauppauge: model = 48139, rev = K257, serial# = 2932857 > tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38) > tveeprom: tuner fmt = PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) > tveeprom: audio_processor = CS5331 (type = 9) > ivtv: Tuner Type 38, Tuner formats 0x00400e17, Radio: yes, Model > 0x00ad2557, Revision 0xdd43f624 > ivtv: PAL tuner detected > ivtv: SECAM tuner detected > ivtv: Radio detected > ivtv_tuner: unsupported module, tainting kernel. > load_module: err 0xffffffef (dont worry) > ivtv_msp3400: unsupported module, tainting kernel. > load_module: err 0xffffffef (dont worry) > ivtv: requesting firmware > ivtv: firmware loaded > ivtv: requesting firmware > ivtv: firmware loaded > ivtv: Encoder revision: 0x02050032 > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > ivtv: Decoder revision: 0x02020023 > ivtv: Configuring WinTV PVR 350 card with 10 streams > ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes > total ivtv: Registered v4l2 device, streamtype 0 minor 0 > ivtv: Create DMA stream 1 > ivtv: Registered v4l2 device, streamtype 1 minor 32 > ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total > ivtv: Registered v4l2 device, streamtype 2 minor 224 > ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total > ivtv: Registered v4l2 device, streamtype 3 minor 24 > ivtv: Create stream 4 > ivtv: Registered v4l2 device, streamtype 4 minor 64 > ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total > ivtv: Registered v4l2 device, streamtype 5 minor 16 > ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total > ivtv: Registered v4l2 device, streamtype 6 minor 228 > ivtv: Create stream 7 > ivtv: Registered v4l2 device, streamtype 7 minor 232 > ivtv: Create DMA stream 8 using 6 103680 byte buffers 622080 kbytes total > ivtv: Registered v4l2 device, streamtype 8 minor 48 > ivtv: Create DMA stream 9 using 32 65536 byte buffers 2097152 kbytes total > ivtv: Setting Tuner 38 > tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c > driver #0 > ivtv: Setting audio matrix to input 3, output 1 > ivtv: Switching standard to PAL. > ivtv: ivtv_enc_thread: pid = 7320, itv = 0xdd4343a0 > ivtv: ivtv_dec_thread: pid = 7321, itv = 0xdd4343a0 > saa7127: Setting Encoder Video Standard > saa7127: Set PAL Video Mode > saa7127: Selecting PAL video Standard > ivtv: Initialized WinTV PVR 350, card #0 > ivtv: ==================== END INIT IVTV ==================== > > I have moved the original tune.ko and msp3400.ko of the original kernel and > changed them with tune.ko and and msp3400.ko from the ivtv package. But > nothing has changed, I can't tune any channel.
After a cold rebooting everything works like a charm. Thanks! -- Oscar Curero - Linux user: 306877 -- GPG keyID: 0xE0EA0B24 --
pgpQl2ibAZdMy.pgp
Description: PGP signature
