Progress. The WintV PVR150MCE now almost works! I get video but no sound yet. This is with the 0.3.6x drivers and the recommended firmware including HcwMakoA.ROM.
I have included the dmesg output after modprobe ivtv from the ivtv driver for both the PVR150 and the PVR150MCE. You will note that the tuner typss are different. With the PVR150 (fully working) I get the following after modprobe ivtv ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.6 (x) loading ivtv: Linux version: 2.6.11-gentoo-r9 preempt K7 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 55, Tuner formats 0x00000e07, Radio: yes, Model 0x008d1657, Revision 0x00000000 ivtv: PAL tuner detected ivtv: Radio detected tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 0 x 12960 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 0 x 12740 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 64 ivtv: Create encoder radio stream ivtv: Setting Tuner 55 tuner: type set to 55 (LG PAL (TAPE series)) by ivtv i2c driver #0 ivtv: ivtv_enc_thread: pid = 14285, itv = 0xf8e2cb60 ivtv: ivtv_enc_vbi_thread: pid = 14286, itv = 0xf8e2cb60 ivtv: Switching standard to PAL. ivtv: i2c client addr: 0x43 not found for command 0x40307603! ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== With the PVR150MCE (only video no sound) I get ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.6 (x) loading ivtv: Linux version: 2.6.11-gentoo-r9 preempt K7 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 58, Tuner formats 0x00400e17, Radio: yes, Model 0x008d2590, Revision 0x00000001 ivtv: PAL tuner detected ivtv: Radio detected tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: i2c attach [client=tda9887,ok] ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 0 x 12960 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 0 x 12740 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 64 ivtv: Create encoder radio stream ivtv: Setting Tuner 58 tuner: type set to 58 (LG PAL TAPE-S001D) by ivtv i2c driver #0 ivtv: Switching standard to PAL. ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== Hope this helps nailing down the problem. Chera Tyler Trafford wrote: >Chera Bekker wrote: > > >>Tyler Trafford wrote: >> >> >> >>>Are you explicitly setting the tuner type? If so, don't. Otherwise, >>>could you post the dmesg log from loading ivtv with the LP card? >>> >>> >>I do not use any parameters when loading ivtv. Should I upgrade to the >>latest unstable drivers? By LP card I assume you mean the MCE card? >> >> > >Yeah, I meant to write MCE. It *should* just work, I'd guess the the >tuner type in your MCE card is not supported by the version of >tuner.ko you are loading. > >Could you locate the tveeprom info from dmesg that is printed when >loading ivtv with the mce card installed? > > ------------------------------------------------------- SF.Net email is sponsored by: Discover Easy Linux Migration Strategies from IBM. Find simple to follow Roadmaps, straightforward articles, informative Webcasts and more! Get everything you need to get up to speed, fast. http://ads.osdn.com/?ad_id=7477&alloc_id=16492&op=click _______________________________________________ ivtv-devel mailing list ivtv-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ivtv-devel
