If I restart X (with gdm-restart, killall X, etc) to switch configurations or something, I get the following log messages then my computer completely locks up. I believe this started in 0.3.7h.
gdm-autologin(pam_unix)[4128]: session closed for user mythtv kernel: ivtv warning: IRQ: IVTV_IRQ_DEC_DMA_ERR kernel: ivtv warning: DMA/UNKNOWN type 0xffffffff, NOT SUPPORTED kernel: ivtv warning: IRQ: IVTV_IRQ_DEC_DMA_ERR kernel: ivtv warning: DMA/UNKNOWN type 0xffffffff, NOT SUPPORTED kernel: ivtv warning: IRQ: IVTV_IRQ_DEC_DMA_ERR kernel: ivtv warning: DMA/UNKNOWN type 0xffffffff, NOT SUPPORTED kernel: ivtv warning: IRQ: IVTV_IRQ_DEC_DMA_ERR kernel: ivtv warning: IRQ: IVTV_IRQ_DEC_DMA_ERR kernel: ivtv warning: DMA/UNKNOWN type 0xffffffff, NOT SUPPORTED gdm[3580]: gdm_child_action: Aborting display :0 gdm[3580]: GDM restarting ... ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.7 (i) loading ivtv: Linux version: 2.6.12-1.1372_FC3 686 REGPARM 4KSTACKS gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 350 card (iTVC15 based) ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] msp34xx: ivtv version ivtv: i2c attach to card #0 ok [client=MSP3448W-A2, addr=40] ivtv: i2c attach to card #0 ok [client=saa7115[50], addr=21] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61] ivtv: i2c attach to card #0 ok [client=saa7127[50], addr=44] ivtv: Encoder revision: 0x02040024 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Decoder revision: 0x02020023 ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv: Create encoder radio stream ivtv: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv: Create decoder VOUT stream ivtv: Allocate DMA decoder YUV stream: 194 x 43200 buffers (8192KB total) tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) by ivtv i2c driver #0 ivtv: Initialized WinTV PVR 350, card #0 ivtv: ==================== END INIT IVTV ==================== ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0) ivtv-osd warning: Framebuffer is at decoder-relative address 0x00510000 and has 1704960 bytes. ivtv-osd: screen coords: [0 0] -> [720 480] ivtv-osd: original global alpha = 208 ivtv-osd: current OSD state = 39 ivtv-osd: new global alpha = 208 (1 255 0) ivtv-osd: framebuffer at 0xf1510000, mapped to 0xe1a90000, size 1350k ivtv-osd: mode is 720x480x32, linelength=2880 ivtv-osd: fb1: iTVC15 TV out frame buffer device ivtv: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total) ivtv: i2c attach to card #0 ok [client=Hauppauge IR, addr=18] ivtv: Tried to open YUV output device but need to send data to mpeg decoder before it can be used ------------------------------------------------------- SF.Net email is Sponsored by the Better Software Conference & EXPO September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf _______________________________________________ ivtv-devel mailing list ivtv-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ivtv-devel
