Hans: I've been following the PVR-500 sound issues with great hope for finally fixing my sound problem. Unfortunately, I still seem to not have sound on my second tuner. I'm beginning to wonder if there is something wrong in hardware. Anyhow, here is my log info:
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.9 (development svn snapshot revision 2702) loading ivtv: Linux version: 2.6.10-1.771_FC2 686 REGPARM 4KSTACKS gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 5 (level, low) -> IRQ 5 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Second (radio) tuner idx 101 tveeprom: ivtv version tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8023936 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] ivtv: This is the first unit of a PVR500 tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #0 TEA5767 detected. ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=60] tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect type set to 62 (Philips TEA5767HN FM Radio) tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61] cx25840: loading /lib/modules/HcwMakoA.ROM ivtv: i2c attach to card #0 ok [client=cx25840, addr=44] ivtv: i2c attach to card #0 ok [client=wm8775, addr=1b] tda9885/6/7: (ivtv) chip found @ 0x86 ivtv: i2c attach to card #0 ok [client=tda9887, addr=43] ivtv: Detected a TEA5767 radio tuner. Enabling radio support. ivtv: loading /lib/modules/ivtv-fw-enc.bin ivtv: Encoder revision: 0x02050032 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv: Create encoder radio stream tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 ivtv: Initialized WinTV PVR 500 (unit #1), card #0 ivtv: ====================== NEXT CARD ====================== ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 11 (level, low) -> IRQ 11 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Second (radio) tuner idx 101 tveeprom: ivtv version tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8023936 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv: i2c attach to card #1 ok [client=tveeprom[50], addr=50] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=61] cx25840: loading /lib/modules/HcwMakoA.ROM ivtv: i2c attach to card #1 ok [client=cx25840, addr=44] ivtv: i2c attach to card #1 ok [client=wm8775, addr=1b] tda9885/6/7: (ivtv) chip found @ 0x86 ivtv: i2c attach to card #1 ok [client=tda9887, addr=43] ivtv: This is the second unit of a PVR500 ivtv: Correcting tveeprom data: no radio present on second unit ivtv: loading /lib/modules/ivtv-fw-enc.bin ivtv: Encoder revision: 0x02050032 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: Initialized WinTV PVR 500 (unit #2), card #1 ivtv: ==================== END INIT IVTV ==================== And here is the output from ivtvctl --audio-status --video-status: cx25840: Status: 0x03 (REV_ID, Revision ID.) cx25840: Status: 'Mono' (Detected audio mode) cx25840: Status: 'BTSC' (Detected audio standard) wm8775: Register R7=000 wm8775: Register R11=021 wm8775: Register R12=102 wm8775: Register R13=000 wm8775: Register R14=1d4 wm8775: Register R15=1d4 wm8775: Register R16=1bf wm8775: Register R17=185 wm8775: Register R18=0a2 wm8775: Register R19=005 wm8775: Register R20=07a wm8775: Register R21=102 wm8775: Register R23=000 cx25840: Status: 0x03 (REV_ID, Revision ID.) cx25840: Status: Video signal present cx25840: Status: 0x01 (MICROCNTL_VIDEO_FORMAT, Detected video format) cx25840: Status: Ready Filter auto tuning status cx25840: Status: 0x19 (TUNE_OUT, The tuning code selected by the auto-tune algorithm.) cx25840: Status: 0x00 (MV_CDAT, Macrovision Copy Control Bits as described in the MacroVision) cx25840: Status: 0x00 (MV_PSP, Macrovision Pseudo Sync Pulses detected) cx25840: Status: 0x00 (MV_CS, Macrovision Color Striping Detected) cx25840: Status: 0x00 (MV_T3CS, A 1 indicates the presence of type 3 of the color stripe process. A) cx25840: Status: 0x00 (MV_TYPE2_PAIR, Macrovision Type 2 pair detected) cx25840: Status: 0x01 (AFD_FMT_STAT, Currently detected Format) cx25840: Status: 0x00 (FIELD, Field status (even/odd)) cx25840: Status: 0x00 (SRC_FIFO_OFLOW, Sample Rate Converter FIFO Overflow) cx25840: Status: 0x00 (SRC_FIFO_UFLOW, Sample Rate Converter FIFO Underflow) cx25840: Status: 0x01 (VSYNC, Vertical sync) cx25840: Status: 0x01 (HLOCK, Horizontal lock status) cx25840: Status: 0x00 (SRC_LOCK, Sample Rate Converter lock Status) cx25840: Status: 0x01 (VLOCK, Vertical lock status) cx25840: Status: 0x00 (CSC_LOCK, Color Subcarrier lock status) cx25840: Status: 0x01 (AGC_LOCK, VGA lock status) cx25840: Status: 0x01 (VPRES, Active-high video present. Indication of the presence of a) cx25840: Status: 0x01 (SPECIAL_PLAY_N, Active-low special play mode (fast forward, rewind, pulse, or slow) Please let me know if there is any way that I can help. I did notice that all modules are reporting that they are IVTV versions except the cx25840 module. Has this module been modified to say IVTV in the logs? BTW, I'm not passing any options in my modprobe.conf file. Thanks again for all your efforts in improving the ivtv drivers. ------------------------------------------------------- SF.Net email is sponsored by: Tame your development challenges with Apache's Geronimo App Server. Download it for free - -and be entered to win a 42" plasma tv or your very own Sony(tm)PSP. Click here to play: http://sourceforge.net/geronimo.php _______________________________________________ ivtv-devel mailing list ivtv-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ivtv-devel
