I'm running SuSE 10.0 with the Hauppauge WinTV PVR 150 card. I've followed the "How To" for loading ivtv-0.4.0 (twice) with the following dmesg output...
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.7 (c) loading ivtv: Linux version: 2.6.13-15-default 586 REGPARM gcc-4.0 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ivtv: Unreasonably low latency timer, setting to 64 (was 32) i2c-algo-bit.o: ivtv i2c driver #0 passed test. ivtv: Failed to load module tveeprom ivtv: i2c client addr: 0x50 not found for command 0x0! ivtv: Error -19 reading Hauppauge eeprom. ivtv: Possible causes: the tveeprom module was not loaded, or ivtv: the eeprom kernel module was loaded before the tveeprom module. ivtv: Failed to load module tuner cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Failed to load module tda9887 ivtv: Could not detect tuner standard, defaulting to NTSC. ivtv: requesting ivtv-fw-enc.bin from hotplug ivtv: firmware loaded ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Configuring WinTV PVR 150 card with 4 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Switching standard to NTSC. ivtv: i2c client id: 0x02 not found! ivtv: i2c client addr: 0x43 not found for command 0x40307603! ivtv: ivtv_enc_thread: pid = 3742, itv = 0xe0ee96a0 ivtv: ivtv_enc_vbi_thread: pid = 3743, itv = 0xe0ee96a0 ivtv: i2c client id: 0x02 not found! ivtv: i2c client addr: 0x43 not found for command 0x402c5639! ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== As you can see, it's still loading ver 0.3.7, which I assume came with SuSE 10.0. I can resolve the failed to load modules tuner, tveeprom & tda9887 by renaming them back as .ko files. However the result is the same, that YAST tries to scan for channels and finds none, and the TV apps fail(Xawtv doesn't load, Kdetv loads but freezes & Zapping loads but can't find any channels). I am beyond my level of expertise and would welcome any ideas. Thanks, Robert _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
