Don't know what happen but I got it work. I try like 10 for it to work and could not get it and I went to work and came back tryed it again and it worked.
>From: Keith C <[EMAIL PROTECTED]> >Reply-To: User discussion about IVTV <[email protected]> >To: User discussion about IVTV <[email protected]> >Subject: Re: [ivtv-users] help setting up Hauppauge PVR-250 >Date: Fri, 30 Dec 2005 10:51:46 -0600 > >On Dec 26, 2005, at 11:48 PM, Crazyguy78 Anderton wrote: > > > I am use the tutorial http://wilsonet.com/mythtv/ > > fcmyth.php#getmythtv and > > try to setup my Hauppauge PVR-250 get to the point here were need > > to enter > > > > /usr/bin/ivtvctl -u 0x3000 and when I enter it say's not an ivtv > > driver > > device what I am I doing wrong. > > >Seems a little strange. Your ivtv log below looks fine. You might >want to verify that your card is getting assigned /dev/video0, which >is the default device for ivtvctl. Otherwise, you would specify the >device like ivtvctl --device=/dev/video1 > > >Keith C > > > vtv: ==================== START INIT IVTV ==================== > > ivtv: version 0.4.1 (tagged release) loading > > ivtv: Linux version: 2.6.14-1.1653_FC4 686 REGPARM 4KSTACKS gcc-4.0 > > ivtv: In case of problems please include the debug info between > > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > > ivtv: any module options, when mailing the ivtv-users mailinglist. > > ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) > > ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKB] -> GSI 10 > > (level, low) -> > > IRQ 10 > > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > > tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > > tveeprom 2-0050: Hauppauge model 32032, rev B310, serial# 6983299 > > tveeprom 2-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2) > > tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) > > tveeprom 2-0050: audio processor is MSP4448 (idx 27) > > tveeprom 2-0050: decoder processor is SAA7115 (idx 19) > > tveeprom 2-0050: has no radio, has IR remote > > saa7115 2-0021: ivtv driver > > saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > > ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] > > msp3400 2-0040: ivtv driver > > msp3400 2-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio > > mode=simpler > > ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40] > > msp3400 2-0040: msp34xxg daemon started > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > > ivtv0: Encoder revision: 0x02040024 > > ivtv0 warning: Encoder Firmware can be buggy, use version > > 0x02040011 or > > 0x02050032. > > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers > > (4096KB total) > > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB > > total) > > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB > > total) > > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > > (2048KB > > total) > > tuner 2-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and > > compatibles)) > > ivtv0: Initialized WinTV PVR 250, card #0 > > ivtv: ==================== END INIT IVTV ==================== > > > > 00:0c.0 Multimedia video controller: Internext Compression Inc iTVC16 > > (CX23416) MPEG-2 Encoder (rev 01) > > Subsystem: Hauppauge computer works Inc. WinTV PVR 250 > > Flags: bus master, medium devsel, latency 64, IRQ 10 > > Memory at e4000000 (32-bit, prefetchable) [size=64M] > > Capabilities: [44] Power Management version 2 > > thanks > > [EMAIL PROTECTED] > > > > > > > > _______________________________________________ > > ivtv-users mailing list > > [email protected] > > http://ivtvdriver.org/mailman/listinfo/ivtv-users > > >_______________________________________________ >ivtv-users mailing list >[email protected] >http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
