On Sat, 2005-12-31 at 18:21 -0600, Bob Karschnia wrote: > I've newly installed FC4 and have been trying to get my PVR-150 to run > but I can't get the audio to work. I've tried just about everything. > It seems like I'm narrowing it down but I've come to a deadend. I > have ivtv 0.4.1 and below is the result of dmesg:
You have an invalid parameter in modprobe.conf for the cx25840 driver. I believe the current How-to says that you don't need any optional parameters for the drivers. HTH, Des > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.1 (tagged release) loading > ivtv: Linux version: 2.6.14-1.1653_FC4 686 REGPARM 4KSTACKS gcc-4.0 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) > PCI: Found IRQ 10 for device 0000:00:12.0 > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > tveeprom: ivtv version > tveeprom: Hauppauge: model = 26552, rev = B268, serial# = 7826786 > tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > cx25840: Unknown parameter `cardtype' > ivtv0: Failed to load module cx25840 > ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! > wm8775 0-001b: ivtv driver > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] > tda9885/6/7: chip found @ 0x86 > ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02040024 > ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011 > or 0x02050032. > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB > total) > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB > total) > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB > total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > (2048KB total) > ivtv0: Create encoder radio stream > tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0 > ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618! > ivtv0 warning: i2c client addr: 0x44 not found for command 0xc0045627! > ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046d11! > ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618! > ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! > ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045613! > ivtv0 warning: i2c client addr: 0x44 not found for command 0x402c5639! > ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045612! > ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c! > ivtv0: Initialized WinTV PVR 150, card #0 > ivtv: ==================== END INIT IVTV ==================== > > It doesn't seem to load the driver for cx25840.......I assume this is > my sound problem. I've tried to load the appropriate modules > into /lib/modules and recently I've found a posting showing they > should be loaded into /lib/firmware. I've tried it with the following > drivers HcwMako(A/B/C).ROM and have copied this to v4l.cx25840.fw in > both directories. > > I can't seem to track this one down. Any ideas?? > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users -- Des Dougan, Principal Dougan Consulting Group Ph: 604-980-2848 Email: des at DouganConsulting dot com www.DouganConsulting.com Design - Implementation - Support _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
